Aussie Locker Install ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 14, 2006
Threads
123
Messages
1,108
Location
Central Cali
LOCKERS HAVE ARRIVED .... :D

AFTER ALOT OF READING AND SUCH ABOUT LOCKERS, I DECIDED TO DO AS MANY HAVE ON THIS SITE, I'M PUTTING AUSSIE'S IN THE REAR OF MY 77FJ AND ARB UP FRONT. I GOT THE AUSSIE'S TODAY AND WAS WONDERING IF IT IS A EASY ENOUGH INSTALL FOR THE COMMON GARAGE MACHANIC OR SHOULD I HAVE THEM INSTALLED BY A REAL SHOP ? THE DIRECTIONS LOOK PRETTY STRAIGHT FORWARD AND I HAVE THE TOOLS HOWEVER I FOUND A SHOP THAT WILL INSTALL FOR $135 AND IT MAY NOT BE WORTH MY TIME AND EFFORT ?

THANKS IN ADVANCE ...

CHEERS .. :beer:
 
It is literally going to take you LONGER to read the instructions, then to perform the INSTALL...
aussie's ROCK :D
 
dude...do it yourself, that way if anything ever happens when your in the middle of nowhere wheelen you can take your axles apart if need be instead of thinken to yourself "oh s***....wish I would done this myself" just my opinion...and from what iv heard the auzzie lockers come with really good instructions and are easy to install....
 
Piece of cake! Just be sure your get your clearances within their printed tolerances, and you will be fine. I had to get some thicker side shims to make it right. But I love how well it works!

Cheers!
 
It is so easy to install. I just put one in the rear of my 40 Friday evening and it took more time to let my gasket maker dry then to install the locker. It took me less than 2 hours to install and that was b/c my 3 year old son wanted to help with his plastic hammer and I was messing around with him making his mom mad that he was getting heavy grease on his hands and face.

Some things to help you out:
Make sure you have heavy grease.
When you put everything in, make sure all the contact surfaces have grease on them to help them stay together until you get the springs in. Be aware that you will probably have to take it at least half way apart at least once b/c of the C clip. Most times, that last C clip will fall out. You need 2 or possibley 3 flat head screw drivers (to squeeze the short side together between the teeth to put the C clip in) a really small driver (like the type for fixing glasses) to help insert or take out the springs b/c of dropping the C clip, a skinny set of needle nose plyers for sliding the C-clip in, lots of rags for your hands (better yet some medical gloves, that heavy grease is a pain). Normal set of wrenches both socket, open and adjustable, a hammer to break some stuck bolts, and some 80-90 weight along with gasket maker or a premade one. If you have a premade one, you will have the whole thing done in under 2 hours and driving back down the road. You should make sure that when you make a tight turn with the gas, you can hear the thing ratcheting. Enjoy! Oh and that loud bang that seems to have made the rig jump and shake all over, that is normal. It sometimes happens when the gears catch. It will not always happen and you will forget it might do it. When it does, it makes the jewels crawl up into the saftey of your stomach.

If you haven't noticed, the springs should have a smaller one inside a larger one. Make sure that it is this way. Years ago when I was installing one in my CJ, I thought 4 springs were for the locker and the other 4 were spares. This didn't allow the locker to engage and I had to take the cover off and spend money on a new seal and more oil. It helps (in my opinion) to use limited slip specific oil. It makes it quieter. I used that and my buddy didn't and his is a lot louder.
 
as said above do it yourself, much easier than you think.

not worth paying someone to do it.
 
The only hard part of the install, if it's anything like an EZ-Locker, is keeping those %&#ing springs from falling into the carrier.

Piece of cake! Just be sure your get your clearances within their printed tolerances, and you will be fine. I had to get some thicker side shims to make it right. But I love how well it works!

Cheers!

Read more here: https://forum.ih8mud.com/showthread.php?t=58648

My link has some pics, but my hands were getting dirty and it was going pretty quickly.

I had one spring go shooting out on me and I thought I was f:censor: ed. I ended up finding it inside the housing!

:cheers:
 
it is way easier then installing a detroit or a arb!
 
I went to install my new Aussie last weekend. I bought some new thicker shims and when I went to test for clearance, I could barely get the center pin in. Basically, there was no clearance.

I then used the shims from the old side gears. This time, one side had the proper clearance (I think it was 0.012), but the other side was still too tight (less than 0.006). So I need an even thinner shim for the one side, right?
 
Way easy install. If you can read you should be able to install the locker. Just pay attention to the clearances. Mine only took about an hour of actual work time, but a week to complete because I had to wait for Toyota to get the proper shims in stock.
 
Aussie Locker Install

[If you haven't noticed, the springs should have a smaller one inside a larger one. Make sure that it is this way. Years ago when I was installing one in my CJ, I thought 4 springs were for the locker and the other 4 were spares. This didn't allow the locker to engage and I had to take the cover off and spend money on a new seal and more oil. It helps (in my opinion) to use limited slip specific oil. It makes it quieter. I used that and my buddy didn't and his is a lot louder.[/QUOTE]

Actually the above note about a "spring within a spring" is for our competitors locker who require two springs to acheive basic reliability. We are able to provide even better reliability by the use of our precision spring, so your Aussie Locker installation kit will contain 4 pins (not shear pins that the other guys use) and 4 precision springs.
 
[If you haven't noticed, the springs should have a smaller one inside a larger one. Make sure that it is this way. Years ago when I was installing one in my CJ, I thought 4 springs were for the locker and the other 4 were spares. This didn't allow the locker to engage and I had to take the cover off and spend money on a new seal and more oil. It helps (in my opinion) to use limited slip specific oil. It makes it quieter. I used that and my buddy didn't and his is a lot louder.

Actually the above note about a "spring within a spring" is for our competitors locker who require two springs to acheive basic reliability. We are able to provide even better reliability by the use of our precision spring, so your Aussie Locker installation kit will contain 4 pins (not shear pins that the other guys use) and 4 precision springs.[/QUOTE]

Opps! That's right. Forgot about that. Thanks for clearing my mistake up.
 
Back
Top Bottom