3FE but no ECU

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 4, 2006
Threads
17
Messages
306
Location
Falls Church, VA
Hi All,

This is my first real post (not replying to anyone). I have a '73 FJ40 with a '76 drivetrain (2F, 4SP, axels). I want to put a 3FE in it with a H55. I have the transmission and can get a complete '91 3FE but may not come with the ECU. My question: should I take it without the ECU? I know I will need to find a '91 ECU for it or can I use something like Megasquirt? My 2F needs rebuilding and this would be perfect, especially since I am installin PS and the pump is already there. But I don't want it if it will be a pain in the a** without the ECU and harness...

Thanks
 
I have an 88 FJ62 3FE ECU from a rig I parted out. Will it work on your 91 3FE?

Sorry, but no harness.
 
I would look into megasquirt...

I think in the long run it will be cheaper, more tuneable, more expandable and easier to maintain. (you'll actually know how it works and what each wire does vs the mystery of OEM EFI)
 
I briefly looked at megasquirt when I thought about rebuilding the 2F, but didn't dig too deeply. I'll take a look again.

Does anyone know how much of a hassle it would be to use a different ECU? I'm sure I could wire it with no harness (would need the ECU (77TLC) - I am an EE afterall.
 
Hi All,

This is my first real post (not replying to anyone). I have a '73 FJ40 with a '76 drivetrain (2F, 4SP, axels). I want to put a 3FE in it with a H55. I have the transmission and can get a complete '91 3FE but may not come with the ECU. My question: should I take it without the ECU? I know I will need to find a '91 ECU for it or can I use something like Megasquirt? My 2F needs rebuilding and this would be perfect, especially since I am installin PS and the pump is already there. But I don't want it if it will be a pain in the a** without the ECU and harness...

Thanks

The harness on the FJ80 is different than the FJ62. I believe the ECU is different too. That doesn't mean it won't work, just be aware that there are differences. I'm going to a boneyard tomorrow to do some more FJ62 harvesting. They have a FJ80 there. I can see if the ECU is a different part number, or if you are sure you want the ECU I can pull it. Problem is, I will have no idea on cost.
 
I would look into megasquirt...

I think in the long run it will be cheaper, more tuneable, more expandable and easier to maintain. (you'll actually know how it works and what each wire does vs the mystery of OEM EFI)

I will agrue that there is no mystery to the OEM EFI.
 
Pappy you need to post up what you did to get the ECU up and running Engine to ECU is easy Power and connecting the right wires from the wiring harness of a 40 to the ECU is a different thing.
 
Pappy you need to post up what you did to get the ECU up and running Engine to ECU is easy Power and connecting the right wires from the wiring harness of a 40 to the ECU is a different thing.

Connecting the correct wires from the ECU to the harness is a no brainer. There are three connectors, just plug them in. Two come from the engine harness and there is no other place to put them. There is a third connector on the engine harness that plugs into the dash harness (mostly power supply). I don't have my notes in front of me, but I know there were seven wires on the 1989 connector. I seem to recall the 1988 harness has two or three wires. Yes, there were two different harnesses used on the FJ62s, and FJ80s are different too.

The third connector for the ECU comes from the dash harness, again no option. This harness is a bit more complex, mostly because the EFI components need to be removed from the rest of the dash wires. Just follow the wires out from the two connectors.

My main issue is I have an engine harness from a 1989, and the dash harness from a 1988. That's how I know they are different. If the harnesses matched it would be much easier.

For the record my motor is not running yet. But from what I've experienced it's not a big deal. The wire diagrams in the FSM are absolutely necessary. This is not a plug and play installation in a FJ40. But with a little research, and spending time with the FSM and the 1988 New Car Features publication, it's very possible for anybody.
 
I don't know if this will help folks or not.

The engine harness has connectors for:
  • ECU (2)
  • Main harness
  • Fuel injectors
  • Cold start injector
  • Ox sensors (2)
  • Cold start time switch
  • Water temperature switch
  • Water temperature sensor
  • Water temperature sender
  • Throttle position sensor
  • Idle speed control valve
  • Distributor
The main harness has EFI connectors for:
  • ECU (1)
  • Engine harness (1)
  • Air flow meter
  • Ignitor
  • Main relay
  • Circuit open relay
  • Vacuum switching valves (3: AI, EGR, fuel regulator)
Plus, it has wires for:
  • Fuse block
  • Speed sensor
  • 4WD switch
  • Brake light switch
  • Ground
That's what I remember. Hope I didn't miss something.

HTH
 
Last edited:
I have a MegaSquirt ECI and relay board with inter connecting cable for sale. I was thinking about doing a MegaSquirt system on my truck be decided to take it Diesel instead.

Peter
 
It almost sounds lilke I should just use the entire wiring harness.

Pappy, I'd appreciate it if you could let me know what year that FJ80 is. If it is a 91 then I might try to get the entire harness and ECU.

No problem. I'll get the year tomorrow when I'm there. The boneyard is in Santa Fe. Closest airport is Albuquerque :grinpimp: :flipoff2:

You have PM.
 
Ok, so it looks like I will have an ECU (Thanks Pappy!).

Now, do I only need the engine harness (which I have) or do I need to get my hands on the main harness?

Check PM. The answer is yes.
 
I am in the process of wiring a 3FE in my 40. I used the complete engine harness and a pigtail of the Main. spliced to a new fuse box and harness. Put the ECU in the glove box.
 
Does anyone need an 88 3FE ECU?

What are they worth?

Thanks
 
Back
Top Bottom