2F Turbo Kit

Would you purchase a turbo kit for your 2F powered 60-Series?

  • Yes, full kit w/intercooler, efi, and ignition control

    Votes: 3 37.5%
  • Yes, but just the essentials (j-pipe, downpipe, bov, wastegate, turbo, plumbing)

    Votes: 3 37.5%
  • No, this is the dumbest s***

    Votes: 2 25.0%

  • Total voters
    8

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

KennyBob

Don’t worry, I went to state college
SILVER Star
Joined
Feb 16, 2017
Threads
88
Messages
1,460
Location
Durango, CO
I love my 60-series in almost every aspect. Like many of you, what I dislike the most about it is the terrible lack of modern power coming out of the old 2F. A lot of folks will say “just LS swap it”. But, as a bit of a purist I love the idea of keeping the drivetrain as Toyota as possible. It occurred to me as it has to some others, just throw a turbo on it! As such, I’ve been working to develop a turbo setup for my 87.

After that epiphany came and went, it then occurred to me that I could develop a turbo kit to offer to like-minded cruiser heads.

With all of that said, is there a market for such a creature out there?

Keep in mind, I haven’t yet proved this can be done.
 
These engines have been successfully turbo'd before. I think the question of "is there a market" will largely depend on pricing and difficulty of install.
Absolutely. 100%. I'm certainly down to figure that part out.
 
I read about one a decade ago I think. And I was all afraid of it then. Now....go get 'em and make whoosh whoosh noises!
 
Do you want an FT turbo as a core to rebuild and use?
 
lets see some pictures of the actual installed parts on a vehicle with before and after Dragy 0-60 times before selling vaporware turbo kits
 
lets see some pictures of the actual installed parts on a vehicle with before and after Dragy 0-60 times before selling vaporware turbo kits
Absolutely fair. Just wanted to get a temperature before I delved too far down this rabbit hole.
 
In terms of power... I have built (and others have too) a handful of 2Fs that put out right at 200 HP and 300 FTLBS. They get better fuel economy than OEM mills (The only 2 that I personally checked into the fuel mileage saw a accurately documented 25% improvement!). They also give up nothing in reliability or longevity. They are as drivable as the original configuration too.

Most people have no real use for more power than this. ;)


On to the subject at hand...

I have had (minimal) involvement with three different turbo set ups. To be honest I don't remember much in the way of details... it has been a while.
One was a fairly Plain Jane FJ60 street/trail rig. Out of, Montana, Wyoming... the Dakotas. Can't remember right now. I do not remember the owner/builder having any complaints about how it turned out and how it functioned/lived.

The other two were built for racing... Yep. Racing. FJ40s racing! Closed circuit rough course racing. The second was built in Oz, patterned after the first which was done in NZ. They were absolutely over the top! Claims of over 400 HO at the crank. Custom pistons and rods, EFI... and yes turbos. ;)

I saw a video of one of them... don't remember which... damn thing sounded like the Devils Own.... Sewing machine... going by at full throttle!

I have no doubt about the HP claims because the guys making them had 100% credibility with me. Okay... maybe I wonder a little bit if they could pull that kind of load again LOL... That does sound outrageous. But still, these guys had no reason to lie to me...

Never done a 2F turbo myself. But the idea has always been intriguing to me. Don't actually have any 2F powered rigs anymore. Currently all my Cruisers have 1FZs or SBC 350s in them. A couple diesel swaps on the distant horizon too.

I do have a project that will be one of those crazy stupid high value FJ40s when it is all done. A 1978 FJ40 (in my opinion THE BEST vintage FJ40.) Low(ish) mileage even! That rig... and the new owner, once we work out the details... might really really like a turbo on top of things.

Absolutely would have to be a blow through EFI. The idea of suck through carbs on turbos was (properly) left behind when *I* was a kid LOL. Personally I lean toward intercoolers on pretty much any turbo set up. That said, water methanol injection can work GREAT in engines that see short periods of high boost needs... unlike a diesel truck dragging tens of thousands of pounds of trailer up a high mountain pass.

Whether I would be interested in buying... well... the price would be a BIG factor. Especially since I am very very aware of how much power a 2F (or a 2FE) can actually make easily with nothing but good old low tech 1970s back yard mods. ;)


Mark...
 
Last edited:
Absolutely fair. Just wanted to get a temperature before I delved too far down this rabbit hole.
You're going to have to do it for yourself. You're going to get a lot of support from keyboard warriors who will never show up with cash to put their money where their mouth is. I would love to have a turbo 2f, but there is no way in hell I'm spending the kind of coin that a properly R&D'd kit would cost to boost a 40 year old tractor engine.
 
In terms of power... I have built (and others have too) a handful of 2Fs that put out right at 200 HP and 300 FTLBS. They get better fuel economy than OEM mills (The only 2 that I personally checked into the fuel mileage saw a accurately documented 25% improvement!). They also give up nothing in reliability or longevity. They are as drivable as the original configuration too.


Mark...
What are the cliff notes on what it takes to get the above? Fuel injected or carbureted engines? Are we talking $15-$20k 2f's with custom internal parts, or is this achievable through machine work and assembling an engine with readily available components?
 
What are the cliff notes on what it takes to get the above? Fuel injected or carbureted engines? Are we talking $15-$20k 2f's with custom internal parts, or is this achievable through machine work and assembling an engine with readily available components?
This was all done... well, the ones that I built... were NOT high dollar high tech animals. Good old 1970s hot rod approaches. Induction, compression, cam and exhaust. Most of mine were running 600 CFM 4 barrel carbs on top of Offenhauser or Clifford intake manifolds, 9-9.5:1 compression (either shaved heads or late model F heads on early model 2F blocks), cams in the 260 (advertised) degree range and keeping it under 6000 RPM (but embracing 5000 happily). A careful static balance of the rotating assembly and a bit of work on the rods to keep everything together at higher RPM. Just swapping the rod bolts for after market "performance bolts (The bolts were speced for chevy BB IIRC).
A couple had slightly larger (chevy) valves. I built a couple of 2FEs along the same pattern. Left the EFI system alone, but some mods there (for flow primarily) would have been beneficial I am sure.

Mark...
 
“ I’m a purist”
Posting about turbos on a 2f.. lololol
To be fair, I qualified my statement. 😂

Maybe the term “oem+” or whatever would be more appropriate.
 
Do you want an FT turbo as a core to rebuild and use?
Hmm, possibly. How does it compare to a T3 or T4 in size? I’ve been researching readily available new turbos for the sake of providing a kit that has support and warranty. I’ve got a dummy T3 size turbo I 3D Printed for mocking up and figuring out spacing. I’m anxious to nail down a choice though. Thanks Galen!
 
If you’re starting from scratch, that probably makes the most sense. Probably just go for a T3.
 
I love my 60-series in almost every aspect. Like many of you, what I dislike the most about it is the terrible lack of modern power coming out of the old 2F. A lot of folks will say “just LS swap it”. But, as a bit of a purist I love the idea of keeping the drivetrain as Toyota as possible. It occurred to me as it has to some others, just throw a turbo on it! As such, I’ve been working to develop a turbo setup for my 87.

After that epiphany came and went, it then occurred to me that I could develop a turbo kit to offer to like-minded cruiser heads.

With all of that said, is there a market for such a creature out there?

Keep in mind, I haven’t yet proved this can be done.
There's a lot of ways to skin that cat, so to speak. Can you talk more about your concept, approach, the equipment used, fitment, etc? It sounds like you're in the planning stages but I'd love to hear where your thoughts are at.


there is no way in hell I'm spending the kind of coin that a properly R&D'd kit would cost to boost a 40 year old tractor engine.
I mean, there's a fair number of people going after 1FZ turbo kits and your words very much apply to that motor too "40 year old tractor engine", etc... Yes I know, more main bearings, overhead cam, yadda yadda. It's a straight 6 slightly diverged from the antiquated straight 6s of old though.

As for turbo 2F sounds ... here's old Mud legend stuff:


Probably the New Zealand truck @Mark W was referring to. There's a build thread around here somewhere...
 
There's a lot of ways to skin that cat, so to speak. Can you talk more about your concept, approach, the equipment used, fitment, etc? It sounds like you're in the planning stages but I'd love to hear where your thoughts are at.



I mean, there's a fair number of people going after 1FZ turbo kits and your words very much apply to that motor too "40 year old tractor engine", etc... Yes I know, more main bearings, overhead cam, yadda yadda. It's a straight 6 slightly diverged from the antiquated straight 6s of old though.

As for turbo 2F sounds ... here's old Mud legend stuff:


Probably the New Zealand truck @Mark W was referring to. There's a build thread around here somewhere...

Howdy Jim! Still very much in the concepts of a plan phase...

But, at the moment I am thinking a j-pipe style mount off of the manifold, keeping it tucked under the manifolds and between the frame rail and the block. I think there's enough room in there, but it'll take some figurin' to find out for sure. I'm thinking low boost (4-5 psi) at first with a 58/55 Dual Ball Bearing .83 A/R or a T3/T04 .63 A/R turbo or similar. Don’t want to crack the engine open for a head gasket and ARP studs just yet. Thinking no intercooler at first to keep it simple, just a short run up to the TBI. Leaning towards an external 44mm or 50mm wastegate. I currently have an Aces EFI unit on it that's just running fuel currently. My plan is to use that to also control timing as it has a 3 bar MAP sensor and can pull timing as needed.

Having said all of that, I'm open to better ideas. I'm not a master fabricator or anything of the sort. Just a cruiser head with a little engineering experience that likes to tinker/make things and also wants my 60 to make turbo noises and mo powa!
 
Last edited:
Howdy Jim! Still very much in the concepts of a plan phase...

But, at the moment I am thinking a j-pipe style mount off of the manifold, keeping it tucked under the manifolds and between the frame rail and the block. I think there's enough room in there, but it'll take some figurin' to find out for sure. I'm thinking low boost (4-5 psi) at first with a 58/55 Dual Ball Bearing .83 A/R or a T3/T04 .63 A/R turbo or similar. Don’t want to crack the engine open for a head gasket and ARP studs just yet. Thinking no intercooler at first to keep it simple, just a short run up to the TBI. Leaning towards an external 44mm or 50mm wastegate. I currently have an Aces EFI unit on it that's just running fuel currently. My plan is to use that to also control timing as it has a 3 bar MAP sensor and can pull timing as needed.

Having said all of that, I'm open to better ideas. I'm not a master fabricator or anything of the sort. Just a cruiser head with a little engineering experience that likes to tinker/make things and also wants my 60 to make turbo noises and mo powa!
I know jack about turbo systems so you're way ahead of me. Sounds like you have a prototype installed? Any photos? I'm also wondering how angry the TBI system would get with a turbo. Sure, theoretically they self-calibrate based on sensor data but scroll through the 60 Series forum here and you'll find a thread like "My Holley Sniper Doesn't Run Right! Help?!" on just about on every page. Seems like it's hard enough to get them dialed in and held there under normal circumstances. That being said I've never heard of the Aces EFI.

As for the location, maybe you could use the EGR cooler threaded holes in the block for bracketry. They're down there and they'd be available - I doubt anybody running a turbo 2F is interested in retaining the EGR system. What diameter pipe would you need to run? Might be able to sneak it between the inner wheel well and the manifolds there since you have to get back up to the intake. Lots of heat shielding might be in order though.

Here's a "wheel horsepower calculator" that's probably 98% bvllsh!t. But hey, just for fun I typed the numbers in. It guesses we'd go from a stock 132hp/198ft-lb at the crank (hey, close enough to the actual 2F numbers!) to 184hp/276ft-lb with 5psi of boost. That's a 36% hp increase and a 39% increase in torque. I mean ... I'd take that. Now factor in my 1mm bore and Delta cam. Maybe I'd go ahead and port the head and manifolds a bit if I were doing a theoretical turbo setup. 200hp and 300ft-lb of torque at the crank? Just maybe? I'm gonna put earplugs in before the LS crowd shows up to tell us how much cheaper you can buy mo' powa' 😂

Now if only somebody would make a blow-through carb setup for a 2F that would be wildly cool ... not because it's better, but for the sheer fact that it's so stupid. It would be fun trying to make it work just for bragging rights. Honestly, your idea even with TBI is just crazy enough to work even if there's no market for it.
 
I know jack about turbo systems so you're way ahead of me. Sounds like you have a prototype installed? Any photos? I'm also wondering how angry the TBI system would get with a turbo. Sure, theoretically they self-calibrate based on sensor data but scroll through the 60 Series forum here and you'll find a thread like "My Holley Sniper Doesn't Run Right! Help?!" on just about on every page. Seems like it's hard enough to get them dialed in and held there under normal circumstances. That being said I've never heard of the Aces EFI.

As for the location, maybe you could use the EGR cooler threaded holes in the block for bracketry. They're down there and they'd be available - I doubt anybody running a turbo 2F is interested in retaining the EGR system. What diameter pipe would you need to run? Might be able to sneak it between the inner wheel well and the manifolds there since you have to get back up to the intake. Lots of heat shielding might be in order though.

Here's a "wheel horsepower calculator" that's probably 98% bvllsh!t. But hey, just for fun I typed the numbers in. It guesses we'd go from a stock 132hp/198ft-lb at the crank (hey, close enough to the actual 2F numbers!) to 184hp/276ft-lb with 5psi of boost. That's a 36% hp increase and a 39% increase in torque. I mean ... I'd take that. Now factor in my 1mm bore and Delta cam. Maybe I'd go ahead and port the head and manifolds a bit if I were doing a theoretical turbo setup. 200hp and 300ft-lb of torque at the crank? Just maybe? I'm gonna put earplugs in before the LS crowd shows up to tell us how much cheaper you can buy mo' powa' 😂

Now if only somebody would make a blow-through carb setup for a 2F that would be wildly cool ... not because it's better, but for the sheer fact that it's so stupid. It would be fun trying to make it work just for bragging rights. Honestly, your idea even with TBI is just crazy enough to work even if there's no market for it.
I don’t have anything mocked up yet, but I 3d printed a T3/T04 someone scanned. I’m planning to use that with some piping to figure placement and whatnot. Other than that it’s all in my head rattling around.

I’ve had good success so far with my aces efi. Knock on wood. It figures it all out on its own (self-learning) for the most part. Although after switching to ignition control and boost, I’ll likely need to learn how to program via laptop I suppose.

I also figure anyone considering adding boost has already desmogged. There is sooo much more room after all that crap is gone. Exhaust is going to be interesting. Back of the napkin/best practice says that a 2.5” j-pipe to the turbo and a 3” down pipe is the place to start. Squeezing all of that in there WILL be the challenge.
 
Back
Top Bottom