steering

Hi, Anyone pull their steering wheel lately? What extractor did you use?

Hello everyone. I am getting ready to do a ton of stuff on my Pig. I am going to start on the power steering. I believe I have most of the big ticket stuff figured most thread I have read hot those.(frame sleeves, TRE adaption, shock mount, pump mount hardware ect.) It's the details I am...

Hi I have a Landcruiser Amazon 4.7 ( uk variant of Lexus). It’s the facelift model 2003. If I accelerate hard from a standing start ( especially in the wet) the car rises and jumps to the left until I assume the attack kicks in . ALSO THE WHEELS SPIN A LITTLE.This must be fault . Any ideas? Oh...

HI all Any other Steering wheels from the Land Crusier models fit a 62, I have a boss kit on mine and want to change it back, I'm South West Western Australia if some one got one for sale or knows of a wreck cheers

I recently bought a 2005 LX470. Seller noted VGRS and VSC lights had been on since around 2017 when he bought it. He told me these trouble lights came on after an indie shop replaced the spiral cable. And VGRS actuator locked at about 90 degrees off. Seller had taken the truck to a Lexus...

Used steering wheel Period correct for post 1981 but will fit earlier years up to around 1974 There’s a crack in the Landcruiser emblem otherwise refer to photos for description $325 USD shipped

I have 2 of them. $25 each shipped

I’m attempting to disassemble my steering column to install a bushing (currently it’s loose in the firewall with a big gap). But I don’t know if I can get the shaft out? Should I be able to slide the ignition switch piece up toward the wheel? First pic. The FSM seems to skip some steps. The PO...

I need a pair of steering arms for fj60. Thank you.

Does anyone have one of these lying around? My column didn’t have one when I took it all apart. Part I need is highlighted in yellow:

snapped mine trying to remove the shaft...anyone have one of these yolks for sale? I'd rather not have to buy the entire shaft assembly. TIA! :)

Hi guys, Getting a popping noise when I turn the steering wheel (can feel the clicking in the steering wheel) on turns with the steering linkage especially when going right. I have shop time and can use the vehicle lift next week, but the vehicle is not currently running. Would love to know if...

Steering Boxes are all the same from 1991 to 1997. This one is not a leaker or a squeaker. Located in San Gabriel/Temple city area. $20 discount if picked up in person so I don't have to plug this one up, wrap it and pack it. Paypal or Zelle Ok. I do not hold items for people unless a 50%...

I have a "Clunk" or Popping noise when turning into a driveway or up an inclined street or drive. I plan on replacing the tie rod ends hoping to tighten up the steering. However is there a set of rubber bumpers or any other part that would be good to replace that could be causing the noise...

I have a torn steering rack boot on my 06 LX can I change it without unscrewing the tire rod end?

My leather has worn through and I'd like to replace it and match OEM look and feel. I've searched Ebay and there's hotboy replacements, but nothing OEM. Searching the forum has returned little results. Anyone have experience using an auto customizer shop? Know a company making replacements?

I needed a larger resevoir to go with the hydto assist kit, also nice to have one that leaks less then oem with a new cap. Psc mounts coming soon. Working on a full kit for hydro assist. These are the brackets I used a 1in ram like @dirtlifestylenate did and love it. Smaller ram means...

Pulled from 1983 FJ60. Worked great no noises. Thought it was leaking but ended up being the low pressure line. Pulled to swap to Saginaw. 190k miles unknown if original. Recommend rebuild prior to install since age unknown. Make reasonable offer via text 6027699800 Jeff

The shaft in my '88 hj61 steering gear box has 4 teeth. I'm being told by the rebuild shop that the replacement shaft with the same PN 44111-60040 has 3 teeth. Anyone ever heard of this? The same part number but different number of teeth on the shaft? How many teeth on a 61/62 sector shaft?

is this a similar process for the fj40.