steering

Manual steering box from a 12/75 FJ40 Works fine. Turns easily. $200 plus shipping

Looks like I need to replace my rack. Any shop suggestions in Santa Fe or Albuquerque?

Hello, Need some help again. Replaced both the tie rod and drag link last week, now the steering wheel can do 1 7/8 turn to the left and 1 1/3 turn to the left. Both the front wheel and steering wheel look straight. I didn't remove the pitman arm during the change. The length of tie rod and...

I was driving home today, while going into a slight curve, my steering got tight and I heard a series of beeps. There are no lights lit up on my dash. Any ideas what this may have been? I just got a new steering rack about a month ago Thanks

My 2010 lx570 is leaking from the driver side rack. Not a terrible leak but definitely getting things wet. Has anyone tried to replace a rack end seal while the rack is installed? Also worrying about the control arm bushing that is getting soaked with fluid being directly under the rack leak. I...

This is not your imagination...it is in very good condition, no broken mounts, all intact, and includes the original screws. THIS IS THE REAL THING!! It is used but not broken at all. $112 includes shipping. Only one available.

I think my PS pump is on the way out. I’m hearing a loud Eeee Eeee Eeee noise when the truck is running from one of the accessories but can’t exactly pinpoint the noise. Took the belt off and can’t hear any noise by hand but there is some in/out play on the pulley. Is this normal or not? I...

Stock pulley, no issues. Keyway doesn’t have any damage and bore is clean. $55 + shipping

Hi Guys and gals I don't post here much, spend most of My time in the 80 forum. I do DD a 2006 Tundra access Cab, it's a great truck and I really like it. It's been virtually trouble free during my ownership. It's a super clean low mile 125k truck. But it has leaky steering rack. it started...

Hi All, I have super fat tyres on my 1976 FJ40. The rubber washer on the steering knuckle is precariously close to the inner rim of the wheel hub. It just about touches it. I am considering installing 5mm spacers but then I will need to remove the wheel studs and extend them for longer ones...

A friend has a 2006 LX470 and the steering locks when turning right at slow speed. In other words, when turning the wheel to the right at slow speed, like a parking lot, the steering wheel will "stop" turning. If he backs off the steering wheel slightly and then goes again, it will then...

I have a brand new, in box steering stabilizer for a FJ40. Price: $100. Buyer pays shipping. I can bring down to Orange County.

Hi, Anyone know the part number for the steering wheel spring ? Thanks, Mike

Hey all, can someone post up pics of what you did for your SAS steering shaft? What parts did you use? I have both an 80 shaft and the 100 shaft. I don't want to reinvent the wheel and start cutting things that I dont need to. Thanks!

I just got my 03 LX a couple weeks ago and knew when I bought it I would have to get an alignment. They had to recenter the rack because the TREs were maxed out. I assumed this was the original rack but maybe it was replaced. The PO didn't mention it and there was no record but it does have...

Rehabbing front end of my rig. 313k miles. Ran into this when cleaning up PS spindle for new spindle bearing, brass bushing, and seal. Is the ID of the axle tube a critical spec? Thinking of just sanding down those ridges (somehow the axle chattered in the tube at some point??). Have a...

Looking for a good used one. Mine is chewed up. PM and/or reply. Thanks!

All, Currently I’m (well my wife is) driving through WY with arms fully stretched out because my steering wheel didn’t auto lower and extend. This has been happening with increasing frequency, the usual fix is stop the car, kill it, restart the car, et, voila. But we didn’t catch it...

Location: Seattle, WA I’m looking for a steering gear box for a 80 series

Ok don’t flame me, I haven’t listed a price because I am asking what these go for and intend to sell them. I briefly researched it and all I could find were horrendous ones or (insane) museum quality… not a lot in between. I have a mudder interested in one and am happy to sell the remaining...