skid

The title pretty much says it. I need the belly and front skid plate for a 60. If you are looking to get ride of either or both please PM me. Frank

The title says it. I need the little skid plate up front and the big belly skid for my 60. Anyone have any ideas or know of a part out locally? Frank

I don't know what specific symptoms this would cause (possibly excess vibration/ NVH), but when I went to install my trail tailor creeper skid, I learned that my transmission mount had come apart. The center rubber section was originally bonded to the lower plate that bolts to the crossmember...

Selling a factory transmission/transfer case skid plate off of a 1984 FJ60. I am willing to ship. Looking for $50

Recently bought an '06 LX 470 that did not come with the engine skid plate. I'm in NE Iowa 45 min from Prairie du Chien, WI An hour from Dubuque, Cedar Rapids, and Waterloo. Have fam in Iowa City. Anyone have a skid plate I could grab? Message me! Thanks!

Got a set of SOR U-Bolt Skid Plates and hardware. New they are almost $300 on the SOR site for the set. $120 for all the hardware you see (plus shipping). Actually, there’s twice as much as this…. The picture is just the two rear plates…. I have to dig the fronts out of the attic. I got a...

Looking for some OEM skid plates for LX470. Toyota classifies them as "under engine cover 1&2". Hoping for something local to WA as shipping will most likely kill any deals elsewhere.

Anyone know the Toyota part number for the OEM front skid plate? I did a forum search as well as looked at some Toyota sites but only found a smaller left and right skid. And before you tell me, I am looking to stay OEM.

Has anyone seen a faulty skid control ECU in one of these? I'm having a unique issue with trac in 4wd on my 2005 sequoia SR5. The following situations are all when taking off from a stop going straight ahead. In 4hi, taking off from a stop, the slip light flashes and power is cut momentarily...

Land Cruiser 100 Series OEM Skid Plate Plastic From a 1999

Good evening. I have a 2020 200 Series LC. I have some of Trail Tailor products installed already and working great. I ordered the Trail Tailor skids for the lower control arms but they don’t seem to fit. There’s a flange that’s extends on both sides that’s keeping the skid Las from seating...

*****SOLD***** Hi all, I have a pair of new 200 series Trail Tailor rear trailing arm skids. I've decided to go a different direction and no longer need these. I did coat these in POR15 in prep for install. I'll put up a couple photos later today. Local sale is preferred, but I can ship if...

Is there some secret code to removing the front skid plate? i have removed that heavy rascal before but this time something is holding it right in the center at the jack point and tranny plug. What on earth am I missing?

Just looking for the stock skid plate. Someone has to have one laying around they don't need. Let me know how much you want for it. Thanks, Scott

I installed my full set of steel skids from slee last night. I noticed that the truck has a slight vibration now. I checked all the bolts and everything is tight. I am wondering if it's the exhaust pipe. It comes very close to the belly pan like 1cm or less. No rattles or squeaks just doesn't...

ALL SOLD! ALL SOLD! ALL SOLD! So I have a few left over parts after selling my FZJ80. I've already listed my JAOS Front brush guard here: For Sale - JAOS Front Bull Bar/Brush Guard + 10" PIAA SUPER4X4 Fogs!!! WAAG Tailight and Rear Bumper Guards! But I also found BRAND NEW IN BOX: 1) JAOS...

Looking for one close to Denver if possible. Let me know what you have. Doesn't have to be showroom quality. Thanks, Scott

These are not a one off project for me, these will be available as bolt on from BudBuilt. That's right, change your oil and filter without removing the armor. Also notice how the alignment cams are protected. Damaged those on my first trip. First off, these are still in development, but...

Was giving my 100 a bath today and found what I think is a yellow hose connector above my skid plate? The arrow is pointing to where I found it. Caught me off guard and couldn't find anything out of the ordinary? Anyone have some insight? or suggestions?

Skid covers for the RLCAs 100 and 200 series. Made from 3/16" HSLA steel Laser cut and CNC bent. Bolt on or weld on 100 kit includes M14 grade 10.9 bolt, drill bit and thread cutting bolts 82.00 shipped 200 kit includes drill bit and thread cutting bolts (bolt can be re-used for the 200)...