rebuild

I blew my old 1F engine and got a 2F and now I am looking at the 3 speed Transmission and Transfer case and wondering if I need to rebuild them. I was getting a really bad whine over 40 MPH, but only on acceleration. I saw one link in IH8MUD where the guy replaced his main shaft and it got rid...

i just pulled my motor, tranny and tcase out of my 95 fzj80 to rebuild the motor after it blew. I want to rebuild the tcase because it was not well cared for by the first owner and I am guessing the fluid has never been changed. My question is what rebuild kit do I need, I have looked a marlin...

Looking for opinions / experiences for any online places I can send a toyota alternator to be completely rebuilt? Has anyone sent theirs out and had good experiences from a particular place? I would like for someone to pull it apart, clean it etc.

I am currently in the process of rebuilding my motor. The motor should be out today along with the tranny and tcase. I cannot decide if I should rebuild the tranny or not, the truck has 275k and next summer I am planning on doing the transcontinental trail so I am leaning towards rebuilding it...

Any suggestions for a company that rebuilds the VAF for the 93 and 94 LC I found this guy off E. REPAIR SERVICE 93-94 TOYOTA LAND CRUISER MAF MASS AIR FLOW SENSOR REPAIR SERVICE | eBay eBay item number: 322406860179 "US $99.95 I AM NOT SELLING AN AIRFLOW METER IN THIS LISTING THIS LISTING IS...

So as winter drags on I start dreaming again. I bough a wakeboat the summer after buying my 40 and now don't want to tackle this project on my own/as a learning experience. I want this to simiply be a driver for the time being and want to get my drivetrain sorted out. I put only about 20 miles...

Well it's not much of a rebuild, but I took apart my malfuntioning I.S. and got it working. Perhaps this has been documented. Drill out the 3 dimples holding the cover on. To remove the cover I clamped one of the mounting ears in a vise. I then used channel lock waterpump pliers to wiggle...

In my 1995 fzj80(271k+ miles) a miss started in cylinder 3 a couple weeks ago caused by what I believe is a injector, I have continued to drive it while waiting for the new injectors to come in. The other day I had to move a non running truck at my shop, so I used my winch to move it, in the...

It's never a good sign when the gear oil is fresh and the drain plug has shavings!

I'm in the middle of rebuilding the drivers side knuckle before I do the other side and have a few questions 1. On the top of the knuckle the bearing had 2 shims, the bottom had only 1. Should I be concerned? 2. what type of paint do you recommend i use after I clean all the grime off?

My '94s power antenna motor decided to unlink itself from the antenna last night. I can hear the motor running when the switch (both up and down) is activated, but no antenna mast action. Does anyone have any experience repairing/rebuilding the antenna drive unit?

If you were to spend $15k on a 40 rebuild (Trail Comfortable and Reliable) where would you go? Only Mountain West Vendors please. Closest to Bozeman will get preference for obvious reason. Thanks! Ryan

where is the best source to get parts for the transmission in a 93' and also parts for the five speed Toyota transmission. cant remember the number on it but its the one people replace the four speed with in the 40's and 60's

Doing front knuckle rebuild on 1974 FJ40. Obtained 1976 FJ55 front knuckles and calipers from mud member. Cleaned and painted knuckles, hubs, Aisen lockers and now ready to install. Rebuild kit and bearings from Cruiser Outfitters.

Is this for part time hubs? About to button up lock nuts and attach flanges had these left....??

Hey all, Been about 4 years since my last post.. Had a kid, and the old bj 40 quit working at the same time... Finally getting around to it for a full rebuild...Got her stripped down and ready to go to the machine shop for a clean up and press in new sleeves, cylinders, etc. The quote was pretty...

Okay - so this is not a build thread per say, but more of a list of what I have done to our FJ60 and an open place for you - the esteemed members of ih8MUD to tell me what I missed and what else I need to do! Here is a copy paste off of my website of what I have done so far. Should you want to...

Hey guys. long time lurker. I need to rebuild my 4 speed in my 87 fj60. 4th gear is roaring.I'm capable of the work but i remember seeing a earlier post detailing the job with some homemade tools. I can't seem to find it now. any ideas or help? I have the FSM but not all the factory tools

I've followed along and learned a decent amount on this forum for a few years now. I figured it's probably time I start my own thread in case it could help someone else out. I'm far from a mechanic, though I know and learn enough to be perhaps be called proficient. The background: I...

When I first bough her, she was a little bit smokey and seemed a bit loud... I thought the somewhat loud pinging was perhaps injector nailing. I drove her for a few hundred miles and figured, what the hey... why not have the injectors cleaned, and ensure that they are opperating at spec. I never...