We used the biggest pot one time, the rest are never used. Complete 10 piece set of Magma nonstick nesting pans, plus omelette pan, plus padded case, plus nesting protectors. These are primarily designed for marine use, but a lot of people love them for camping due to their compact design. We...
Hey guys, the clutch was on its last leg and I decided it was time to change it out. The oil pan gasket was leaking and figured we might as well replace the gasket. This was sitting in the oil pan, any ideas what this is???
Chasing a leak which seems to be coming from the lower oil pan, so I need to pull it off and reseal it. The bolts looks pretty nasty so I want to replace them with new, OEM ones. Does anyone have a part number on the lower oil pain bolts? Thanks!
I’m in the process of replacing the glasses on my oil plan. There is a post from @Poser that I have been using as a guide. He uses a carquest supreme black gasketing silicone sealant for the corners and on the saddle of the gasket. I couldn’t find anything similar at the auto parts store so I...
Hey mudders,
Looking for a square 🔳 cast iron frying pan for camping. The kind with out the "ribbs", just flat.
Searched high & low.....no dice (as of yet).
Reason: will fit better in my kitchen box on it's side without rolling.
Thanks in advance!
I have a FJ40 with a '85 FJ60 2F Engine Swap.
Oil pan is leaking under the "bash plate" - probably from one of the welds.
Any recommendations on parts vendors with good prices and reasonable shipping?
I found this - seems fairly recent. Can anyone confirm the part number for the pan and...
Looks like in some point in time someone wrapped the leaking oil drain plug on my 2005. Anyone removed oil pan #2? Did you have to Jack up the engine due to the interferences?
I’m thinking I’ll just use a steel cup brush to bash away the FIPG or whatever that is, open my drain plug and replace...
Pulled the oil pan on my 91 FJ80 with the 3FE to finally tackle the oil leaks! Valve cover and pushrod cover have been done so this was next on the list.
Pulled the pan off and noticed the paint on the left side was pretty bubbly. Got to working on the wire wheel and found a few small spots...
As some know I am changing my oil and the PO had "gooked" up the oil pan plug with Permatex and a Toyota gasket. I removed the plug and Viola! there is a dent at the six o'clock position where the gasket goes. I am planning on using JB weld to level the dent out. Is there a better product or...
So I'm confused by all the oil pan part numbers out there. I have a '71 with the original F motor. According to toyotapartsdeal.com I need part number 12100-60060 which has been replaced with part 12101-61013. BUT, when I search the newer part number, it seems like that one is for later 2F...
Just wanted to see what thoughts are on this. Not mine, Rest of truck loooks nice, undercarriage light surface rust but this just concerned me a bit. Is it a metal patch over a rusted floor pan? Thanks
Hello
I purchased a 97 lx450 a few months ago with all the normal oil leaks. Thanks to Mud I was able to fix all but one last leak. The last one was the oil pan arch /rear main seal leak. Oil was on the bell housing. Thinking the oil pan arch was the cause of the leak, I went that route to see...
Th below pictured transmission pan is on its way to my place for testing on the Land Cruiser AB60F transmission. It is a prototype in the as cast finish. Fluid capacity has been increased by 3.25 quarts, so the total transmission circuit should hold almost 15 quarts total. How much cooler it...
So i ordered a 2.4LTE received it and it was out of a hiace van. long story short the oil pan will interfere with my front axle. im needing one that will fit with its own built in dipstick.
let me know what ya got
801-564-9029 Ryan
Did a Rodney flush this weekend. Im curious if the amount of fine smutz collected on the pan magnets is normal. It's been a about 30k since the last trans service. 247k miles on the vehicle. What do you think?
Just doing the timing chain on my 1989 22r engine. My book says to lift the engine about 1 inch and pull it out. I tried that - no go- lifted it over 2 inches and still no where close. It doesn't even seem like I will be able to lift it high enough to get it out. Does it have to twist out...
Please help. New here and recently inherited a 1995 Toyota Land Cruiser. Love the beast. One problem, the Tranny pan is leaking, very rusted. I am spinning my wheels (or actually not with no fluid) trying to find a pan. No one seems to have one. Anyone have any ideas, or maybe one laying around...
I have a set of LC Heaven floor pan patch panels for an FJ40 the 79+ variety
After I bought them, I realized the entire floor really needed to be replaced so these are not needed.
$200 + shipping for the pair. These are on hand and you can have them in a few days.