intake

Currently have my intake and exhaust manifolds out to replace gaskets and hopefully improve a low vacuum condition on my 86 FJ60. Having trouble to find a machining shop that knows how to handle the assembly to clean it up and get the full surface flat. Mixed material between the exhaust and...

I have a 7/70 FJ40 that I'm trying to get back to as close to stock as possible. I can get a later 3 piece intake/exhaust that I want to put on my motor. I've seen a few opinions and couldn't come to a clear yes or no. Will the setup below bolt on? Thanks.

I'm trying to figure out how to mount the intake horn from a '76 on the 2F I have in my '71.....can anyone post a picture of the bracket and how it mounts to the front bib (see picture below for reference)? I can't find any pictures looking at that area from behind. I just need to know what...

Stock 3B intake hose US$40 plus shipping

So, found out I have a leak in the plenum gasket, I’m pulling the upper off when i get the parts in, but under there I know are a bunch of VSV and VCV, I know some are related to ERG, I was getting the code a while back but did the resistor fix and now don’t really need a lot of these under...

I just rebuilt a 1976 2F and the machine shop showed me my intake had been welded with a tasty weld bead right in sight (no leaks) but with an expensive fresh rebuild I want my Cruiser to breath and avoid any ashtma issues. Also, my exhaust heat riser flapper (technical term) leaks and I am...

Anybody running this combo? I currently have an offy intake, Holley carb, Downey (I think) header combo on and 82 fj40 a runs great but would like to take it back closer to stock. I have all of the parts except for a stock manifold to go back, but the headers look to be in great shape to would...

I'm doing the 3fe exhaust mod and I'm not sure my existing intake manifold is going to work out. It's not cracked, but you can see the eroded aluminum. Is this okay? I'm not looking for a ported intake, but will this be a future problem? As I guessed it's not completely flat. It's off by 0.020.

I have two (2) sets of brand new Toyota intake boots for the 3FE 80 series. I originally ordered them from a well known west coast parts supplier but they showed up WAY late, so by the time I finally received them I had already installed a set from some where ells. I'm also not sure why I got...

2003 lx470 There is a front plastic cover on the air intake connector that completely popped off the other day, I'm not sure what this is for. I was getting running lean codes randomly before and I believe this was loose and the culprit, struggling to start when truck was hot. I've tapped...

Bought a semi-local PDI intercooler kit for HDFT to adapt to my 1hdt, and they are exactly the same aside from one pipe and the manifold adapter. I need the intake manifold adapter, as well as the straight/45* pipe that runs along the valve cover on my HDT. The pieces I need I have circled in...

The subject line says it all. My coworker was revving it and flames shot out, I now realize that's not the most ideal thing to have happen. Could I have burnt a valve, or caused any other issues? Since I recently diagnosed the intake leak im now thinking its not as cool.... lol! Newly rebuilt...

The subject line says it all. My coworker was revving it and flames shot out, I now realize that's not the most ideal thing to have happen. Could I have burnt a valve, or caused any other issues? Since I recently diagnosed the intake leak im now thinking its not as cool.... lol! Newly rebuilt...

Would anyone know the manufacturer or distributor?

Looking for an air intake for a 14B-T intake manifold (not the manifold itself). Can be posted to Houston, TX. Addresses in Australia and Europe also available.

I was replacing hoses under the intake manifold and saw this wire cluster that plugs into a Blue & Red "sensor/relay" and then into a white plug. This cluster also appears to run down the block a few feet and plugs in again there. My question is, what is this plug/wire assembly called(part# if...

Looking for a horn and bracket for my resto-mod. Need the horn definitely….i can make a bracket if I need to. Please message me if you have one available. I plan to sandblast and powder coat, so I don’t need a unicorn part….just no structural rust, please.

I searched but only found info on the F engine studs. Does anyone know what size/thread are the studs that mate the carb to the intake manifold?? Mine are toast, can't seem to find replacements! I need the specs for them in order to call out-of-town shops..

This is a very specific one…1975-1976 Hot air intake insulator. This is specific to non-thermonuclear, one-piece exhaust manifolds. Great shape, just needs blast and cerakote for nice appearance. Too early for my truck else I’d install. $50 + shipping

Hi all, Trying to tune the 60 but its proving difficult doing the lean drop with this aftermarket chinese carb I'm running with. Using a line from the intake I get 12 mercury, but i know the ideal range is 15-20. will this increase as I get closer in tuning this, or do I have vacuum leak? Im...