hubs

I am looking for some rear full float hubs off an 80 series. Let me know what you have got. Thanks

just pulled in vgc,have all cone washers missing 2 cap bolts $125 shipped or best offer

Curious to see what other 100 series owners have done with the lug pattern on their off road trailers. As we all know the 100 series utilize the 5x150 bolt pattern which can cause some issue in finding a matching hub pattern to run a similar or matching wheel to the tow rig. Outside of using...

I've always wanted my locking hubs to be red so I painted them today. I don't think it turned out bad. I figured it couldn't make it look any worse. It took me about 30 mins and cost me about 50 cents.

Great condition front axle out of an early 80's BJ40. 4.11 gears and Aisin hubs. No rust. $500 picked up in Las Vegas, NV, or I can ship via Fastenal. Thanks

I just wrapped up my birf overhaul with the new Aisin hubs on my 97 LX450. I had the 2nd groove machined on my axle and everything went great until I had to put the snap rings on. the new groove and ring seated perfectly but I wasn't sure if I still needed the original clip. The outer...

Yeah, we stock that! Are you in need of some new AISIN hubs for your Land Cruiser or Truck/4Runner? We've got the cure! We stock more AISIN hubs than anybody, pallet loads. Chances are we not only have exactly what you need but in a color of your choice too! Fits 8/99+ 76/78/79 Series - w/5...

I have a set of used Aisin hubs with chromoly inners. They are currently on an FJ40 axle with 30 spline longfields. Asking $180 shipped.

I need two locking hubs for '78 fj40 Please let me know what you have. Thanks. A.J

Looking for a pair of good working order Aisin manual locking hubs 30 spline with associated nuts and bolts, to 98579. Thank you! Dave

These bearing hubs were off an 84 FJ60. Both have been bead blasted. One has been 2 part epoxy primed and painted with 2 part Imron satin black. Some pitting, but nothing to keep from running these. $40 plus shipping for the painted one (pictured) $30 plus shipping for the non painted one.

Any demand for 1974 front knuckles, locking hubs and trunnions?

My 5/1980 came with drive flanges. I have access to several sets of locking hubs. What do I need to look for / check to ensure they will fit and operate correctly ? Thx

Quick question for you 60 guys, Can you still buy NEW hubs and flanges from the dealers. I'm not talking about the locking hubs. Thanks! I just bought a Diamond axle and it came with used hubs and flanges.

We have too much of this stuff laying around collecting dust ...... Total of 3 coarse spline birfs and 2 locking hubs. $25 plus shipping. They'll fit in a medium USPS priority flat rate box. Georg @ Valley Hybrids & Cruiser Brothers

Hello mudders I found a set of hubs with PN 43530-60042 (1) 43530-69055 (1) Is the 2nd one the correct pn for the80s? ( Still modifying the birf) Thanks in advance

Looking for a Pair Front spindle hub in good condition.

Can someone please share your experience if you have AVM462HP wheeling hubs installed? Is it truly plug and play? I know @LandCruiserPhil spent hours grinding to make them to work on his LX470. I am looking to order a set but I am a bit concern they may not be plug and play.

Rebuilt 3 Aisin and 1 Asco Land Cruiser locking hubs, cleaned, bead blasted and painted face and lockplate, new balls, bolts, o-rings. 30 spline 79-88? Paper gaskets included. $80.00 each or $150.00 a pair plus shipping $14.00 Please PM Thanks, John

I recently parted ways with the body and frame of my parts car (1975 FJ55), and now have these complete axles left over. Willing to sell them complete or in pieces, just let me know what you're after. Uber-reasonable pricing. I'd prefer not to scrap them if people need parts! Buyer to pay...