hubs

Hey folks Having a wee issue with the 4wd on my bj60. Back in August I tackled the front axle of my cruiser, replacing as all seals and bearings, and following what I thought was the standard disassembly/assembly procedure. A Greasy job that one. Anywhoo since I slapped it back together I've...

Brand new in box warn premium locking hubs. Model #28771 30 spline. $100. Can send actual photos with any information you need, but wanted to get post up while at work. Reach me fastest at 509-638-8707 Jharkness13@gmail.com

Someone recently stole the front hubcaps off of my stock wheeles so i just removed the rear ones and i dont mind the look. I plan on spraying them with bed liner. However there are center bolts? Lugs? Not sure what they are, missing from the rear wheels. Can anyone tell me what they are/ their...

I have a set of working Warn 6 spline hubs from my FJ40. I am doing a FJ60 series front disc brake swap and they are no longer needed. No rust etc, but do need cleaning / restoration. Asking $65 plus shipping. Paypal/Venmo preferred

FJ80 with ABS Knuckles $125 driver side, $75 passenger side. FJ80 without ABS Knuckles $125 Driver Side, $75 passenger side Steering Arms, etc. FJ80 Spindles, Hubs and axle shafts. 4.10 Ring and Pinion NO THIRD MEMBERS, NO AXLE HOUSINGS All parts can be shipped in USPS flat rate boxes except...

Replaced all the parts you see in my truck with brand new stuff. I'm not wheeling and I don't have space to store so I figure it should go to a member who can put them to use as trail spares or re-condition them before putting them in their rig. The part that looks the worst is the driver side...

Worked fine when I pulled them last year. I will ship anywhere in the lower 48 on my dime. $80 for the pair OBO. Thanks, Kevin

I have a complete front axle out of my 1966 FJ40. It's all there and everything is moving freely. Should be usable as is but will need brakes. It would be good for parts too or a restoration or a SOA conversion. I'm located in Washington State. Come and get it, no shipping, local pick up...

Hi Mudders, Looking for your experiences with wheel bearing replacement and how well they held up. I'm personally reluctant to buy China for fear of failure like I've seen in friend's vehicles. I'm hearing some major brands (SKF, Timkin) are manufacturing in China so I'm wondering if the...

SoCal FRONT ONLY FRONT ONLY FRONT ONLY Please specify year of your FJ80 since 91-92 uses a different system. Also have axle housings, steering arms, etc. Prices range from $40 to $125

SoCal Prices run $50 to $100. Warn Hubs Birfields Steering Arms Inner Axle Shafts Knuckles Shipping available

Hi there guys, This may seem like a silly question since one would assume that if you own a 4x4 then you should have all of this under your belt. I just cannot figure this out since my truck has manual locking hubs. My truck has manual locking hubs. It also has the 'HUB LOCK' switch. I also...

Do you guys have or know where I can get replacement (used and in good condition) 6 spline Warn premium locking hubs? I have a 1971 FJ40.

SoCal Send Personal message for requests and prices.

I have a '99 LC that I would like to install part time front hubs on. Can it be done and if so does anyone have the correct ASIN part number? Also is there anything else that needs to be done when the hubs are installed. The wheel bearings have just been packed with new seals.

I suspect it's 'Tire World' - the manual hubs on an FJ62 I'm working on are both locked when in the 'free' position, and only turn 2/3s of the way toward 'lock' (and this makes no difference in their status). I jacked up the front of the truck and went through all possible combinations to...

Are there a year range that the mini-truck knuckle balls, spindles & hubs are the same as FJ60/62? Where I live FJ60/62 are few & far between, but there are lots of mini-truck of all years around. If they are the same in a certain year range it will make getting some a lot easier. Cheers, Allen

I'm looking for a pair of locking hubs for my 81, brand is not a concern as long as they are in working condition. Thanks. A.J

I swapped to hell fire knuckles. So I have the stockers. THey have new (but installed/removed) timken trunion bearings and both steering arms that INCLUDES THE OVERSEAS one for a front-side tie rod. I will ship them out for 200 to within the 48 states. OBO if its up for a while. REAR FULL...

Anyone here have any idea why Toyota put 5-bolt hubs on some or all of the HZJ105's? I'm pretty far away from civilization and both of my coworkers' 80's have 6-hole wheels. Kind of annoying that we can't share extra spare tires when things get ugly. Also puzzles me why Toyota would want to...