fzj

https://bringatrailer.com/listing/1997-lexus-lx450-74/

Looking for good condition, illuminated, tan sun visors for a 97 Land Cruiser. Thanks,

Considering buying a 80 and trying to find some reputable places in these areas. Please let me know of any places, would be greatly appreciated! Thank you!

Hi guys, I have a 1994 petrol FZJ80 MT. The compressor turns off when idle (RPMs below 1000). If I step on the gas an bring the RPMs back up it turns back up. Does anyone have any idea what might be wrong? Thanks!

Newbie to i8mud but long-time cruiser owner. Not sure where to post Sioux Falls area Time to thin the heard., I have a 97 cruiser, body totaled, mechanically all there, no lockers. runs drives and stops. 200,000 miles. no rust, t-boned on pass side, 95 cruiser white, rusty, lockers, zero...

Interested in a locked 80 95-97 cruiser or LX preferably 12k or less. Clean well maintained. I'm located in AZ so Southwest is preferred but may travel further for a good deal.

Need a good condition heat shield above where the cats go (i have the dual side by side cats)

**EDIT: FOUND ONE. THANKS. Looking for one as pictured below. Thanks.

I have no idea why anyone would want this, but I sold one off of a '01 100 a few years back so here goes. Rear Spoiler off of a '96 FZJ-80. I do not have the brackets. $10 OBO.

1994 FZJ-80 land cruiser distributor, used. I had it for a spare. $100 shipped in conus.

Completely stock 1993 FZJ80 with just under 141,000 miles. Has all the options, including factory electric front and rear differential lockers (both in working condition). New brakes, radiator, and radiator hoses within the last 1,000 miles. Runs and drives great. Check engine light is on and...

Off the Market: Basic Specs: - 1995 FZJ80 - 180k miles - TRD Supercharger (55k miles on it) - Slee FR, Rear Steel bumpers - had swing out tire carrier and 2" receiver added on to rear later - WARN M12000 Winch with remote - Sliders - Transfer Case skid plate - Cloth Interior - no drilled...

So I recently picked up a locked 96 black Lexus LX450.. ABSOLUTELY LOVE IT ! But the seats never worked in regards to the forwards and backwards motion. I did some research online and came across Gamiviti gears. I ordered 2 caps and two gears and went to work yesterday, tackling both drivers and...

So I followed this 'how to' fj80 and lx450 ps pump rebuild Got everything torn down, seals replaced then I got to the shaft seal on the inner cover and noticed that the o-ring that came in the Toyota OEM rebuild kit is just slightly too big for the ID of my cap. (Also found out why it was...

Are there any cheap M-OBD readers out there or does anyone have any experience with them? My 01 FZJ100 is not obd2 compliant and uses M-OBD and there isn't a lot of info on it, the most I could find was this company that offers an M-OBD tool for $200 Scanner - Scantool - OBDI - OBDII - OBD2 -...

Edit: sold, for $3500. I looked for over a year before I found this cruiser. I REALLY hate to get rid of it, but it has a blown head gasket, and I can't front the money to do the work. I'm going to have to sell it and use the money to buy a cheap daily driver. Maybe I can rejoin the club in...

I have several sets of rigid duallies. I will sell them for $50 a light (that's $100 for a pair) obo. They do not come with wiring, just light, mount and plug. Spots and floods. I also have a red factor 55 thimble (sold). Two pairs of wheel spacers in good shape. 1 pair of 1.25 wheel spacers...

I am looking for a set of 80 Series wheels near the KY TN area in good condition. Thank you

For a while my land cruiser's transmission has been acting up. It won't shift into reverse or 3rd gear until it gets warm, the reverse dash light does not come till it gets warm either even after it does it still slips for a quarter of a second till it finally goes into Reverse or 3rd but then...

Quite a while ago I stumbled across a sensor hanging by the wire in my engine bay, after a quick search on the web I realised it was a Door position sensor so i unplugged it and stored it in the car for a while so i'd have one less thing dangling in my engine bay . Today I decided to research...