fj80

I am looking for a clean, low-mileage, rust-free, LHD, 1991 or 1992 FJ80, w/ 3FE engine, and NO SUNROOF. Even better if it has manual windows and door locks. I don't care what color. Some people might refer to this as a "Poverty Pack" 80 series, although I think that term technically only...

Hello everyone, I have been on the look out for a torque converter for my 1991 80 series. I have a transmission to install but was a new or rebuilt torque converter. Dose anyone know where I can source one?

Hey all, I bought an 1997 hdj80 with h151 to swap my 3fe and auto trans out my 1992 jdm cruiser. My question is I have seen where the part numbers for 91-92 are different of that of the 93+. Can the 97 pedal set work in the 92? Or do I have to source a 92 pedal set? Regards Dan

Has anyone gone and seen this thing? Curious about build quality etc but the pics are tiny and seller has no real history about who did the work and when..

I need some headlight gurus to chime in. My headlights went out at the same time . I checked the fuses and they were blown. So I replaced those fuses and still nothing. I then checked out the relay, I hear it clicking. So that’s not the problem. I swapped out the headlight bulbs (inner ones)...

Hey guys the LKQ in Raleigh, NC (Clayton) has a 1991 FJ80. Body is solid and no major rust. Again this isn’t mine, I just thought someone may need some parts from it.

$300 for the entire set with the front covers installed. No shipping. Pickup in Socal. Text me at 562-665-8453 As the title states.. I have a complete grey leather seat set out of my cruiser. I'm leaving the LSeat covers on the fronts when selling but they are pretty beat and missing chunks...

Does anyone have a recommendation for a replacement brake booster? I need to replace mine and was looking for a quality aftermarket alternative.

parting out 91 FJ80 started a motor swap to a 1fz when the 3fe started knocking. I have all engine and trans components and all body parts except whats listed as sold. I am currently working 50 hours a week and going to school so please bear with me on reply time. transfer case SOLD rolling...

Greetings friends. New to me 91 FJ80 with 227k miles. There is a red wire coming off the ac compressor that is not connected to anything. Anyone know where this should be attached? Farther down near the oil filter there is a white/grey plastic connector that is missing a connection but I’m not...

Like new front, second row and third row GREY. These ONLY ARE FOR 1991 AND 1992. (THE BUCKLE CLASP PATTERN IS DIFFERENT). FRONT BELTS: DRIVER $125 PASSENGER $95 SECOND ROW: each side $60 THIRD ROW; each side $25

1991 FJ80, a while back I had a shop who said they were experienced with Land Cruisers rebuild the front end -- axles, steering knuckles, maybe some other stuff, I don't remember. The axles they used were aftermarket, they have two outboard grooves for a snap ring, I suppose for different...

Selling my labs bike carrier, this is discontinued but I was able get a hold of an extra one that Luke had laying around. I believe this fits on both 80 series and 60 series 4x4 Labs rear bumpers. I used it a handful of times to transport my mountain bike. Holds two bikes. $550 OBO Currently...

FOR SALE: 1991 Land Cruiser. 143K miles. Excellent condition (for age). Stock. Sunroof. Have original window sticker and Car Fax from 2020 (no accidents…). No rust. There are a few paint scratches and a couple of small “dings” in paint. Originally had 3 rows of seats, but no longer has the rear...

I can send pictures but I have a Safari Bumper, Temp Control unit (I have 2! ! is perfect and one has the temp slide broken but could be used for parts), Original Jack, Mid Seats OEM mat, Rear OEM mud flaps, Center shift console plastic in tan, Center temperature Bezel plastic with 12 volt plug...

Have a pair of used Corbeau XRS Baja seats w/ Corbeau FJ80 sliding brackets. Seat brackets part # D988/D989 Pass seat has a very small burn from an ember at a camp fire.. Seats work great and slide back much further than factory.. Retail on seats is $959 a pr and seat brackets run $278 a pr...

Does anyone happen to have an armrest base for the front driver side (LH)? The top of the handle on my armrest base broke off where it screws into the door panel. The trim is brown, which I believe is called "oak."

Looking for overhead con. And sun visor

Hey guys ! First post here, I’m redoing my breaks and having some serious issues getting off the spindle nuts. If anybody is local between San Diego to Hemet and could loan me the 54mm spindle socket/ or a hand I’ll gladly reimburse with a case of beer.

Looking for a working AFM. Located in SoCal and willing to drive for pickup. If out of state please provide shipping cost to 91344.