fj80

Have a pair of used Corbeau XRS Baja seats w/ Corbeau FJ80 sliding brackets. Seat brackets part # D988/D989 Pass seat has a very small burn from an ember at a camp fire.. Seats work great and slide back much further than factory.. Retail on seats is $959 a pr and seat brackets run $278 a pr...

Does anyone happen to have an armrest base for the front driver side (LH)? The top of the handle on my armrest base broke off where it screws into the door panel. The trim is brown, which I believe is called "oak."

Looking for overhead con. And sun visor

Hey guys ! First post here, I’m redoing my breaks and having some serious issues getting off the spindle nuts. If anybody is local between San Diego to Hemet and could loan me the 54mm spindle socket/ or a hand I’ll gladly reimburse with a case of beer.

Looking for a working AFM. Located in SoCal and willing to drive for pickup. If out of state please provide shipping cost to 91344.

Asking $5,250, with no more time money or energy to put into this vehicle i am putting it up for sale. Like everyone in here I have put a ton of money, effort and time into this project and I am now trying to cut my loses and recover as much as I can. This is a stock ‘92 that I picked up in Feb...

Done a lot of research and looking for advice regarding my heater. ‘93 FZJ80 - My front and rear heaters blow hot for about 10 seconds then become lukewarm. A/C blows cold and all blowers, modes, and vents work. Heater control valve on firewall is new and opens / closes properly. Back flushed...

1996 FZJ80. Guessing this works for all 80's. Part #8151560361. I need 2 of the pigtail wiring setups. I don't need the lens or housing. Please PM me if you have them. Thanks.

All from a smog passing good running 3FE. All connectors intact, ready to install or clean and install. 175 shipped for all 4. CHEAPER THAN BUYING ANY TWO OF THEM! Prefer to sell as a set of

Looking for front seats. Must be manual adjustments (not electric). Brown/tan preferred but it really doesn't matter. Thanks Jeff

This switch panel has been on my desk at work for about 10 years when it was removed from a part out. I’m certain the partout was a 3FE so this is an FJ80 panel not an FZJ. $140 shipped to the lower 48.

Howdy folks, On the hunt for the following: -FJ55 Orange 4WD Tail Emblem -FJ80 Chrome Electric Side Mirrors (both left + right) -FJ80 Chrome Door Handles (all 4) -FJ80 Beige Passenger Side Sun Visor Shoot me a DM if you have any of these! Willing to pay for shipping. Thanks! Sincerely, Your...

Hey all, Just picked up two JDM cruisers, one is a 2-door Prado posted over on the 90 forum, and this VX Limited. Wasn't as thrilled to have the 3FE, but this thing makes up for it with the additional goodies that we didn't see over here, and it is oh so clean. Unbelievably well-maintained...

I have two sets if OME bushings and a Slee caster plate kit. Bushings. SOLD Plates. $80 each These retail for $139.00 I will ship any set for $100 flat rate box Open to offers. Let me know if I am high on price. Located in Richmond VA. 23230. I can ship out in a flat rate box.

So I am finally going to buy a winch. I bought this rig with the pictured ARB bumper that does not include a space for a winch. Sale does not include lights or red tow hooks. Otherwise a great bumper available for pick up in Atlanta. Asking $475

Hello everyone, Been on here a little but military life has been getting in the way of me digging into my LC. I've finally got back to the states again and have time to get some stuff done. I have done some searching on here and other places online and am trying to find if aftermarket...

Hey all, I justified buying an 80 to cart the kids around…and mamas starting to ask questions about when the third row is going to show up 😄. Looking for the third row and all associated mounting hardware/seatbelts near Phoenix, AZ. I’d prefer brown cloth, but open to any colors. Thanks!

I’m trying to trouble shoot a pressure failure in my n.d. 80 series pump mated to a 86’ 60 series PS box for eventual installation in my 78’ 40 w a 2F. I’ll be building a custom bracket so the pump can go on the drivers side (LHD). I have a PS pressure testing kit spliced into the setup. I’m...

I've been dreading the day that I commit to replacing my starter and cables. I bought the cable kit from @Fourrunner back in January because I have that intermittent non start issue. I also decided to get a remanufactured Toyota starter from the dealership. Yesterday was the day and though it...

Can someone tell me where to connect the vent hoses coming off the distributor cap? I do not see the distributor on the vacuum diagram on the hood. I also discovered that my vacuum lines were not connected correctly from the previous owner and boy did that make a difference in the idle!