distributor

For sale, 19100-61080 distributor new PLUS clamp. this is referred to as the non US distributor. $220 plus shipping from 77005 - Venmo

So to my understanding my 72' 1.5F motor has a vacuum switching valve for emissions. Since I don't know if this early emission control works and im having trouble tuning my carb I decided to eliminate it. A previous thread discussed this and blocked off the intake manifold port and lower carb...

Hey, This is my first post on this forum and I am happy to be one of its members. I have a problem in my FJ73 3F engine with the carburetor, it was not original, and I bought a new original carburetor. But I noticed that the distributor need to adjustment, and I set it well, but the problem is...

Vacuum advance for 19100-61102 for sale, working. $75plus shipping from Houston TX - price updated

19100-61102 "BIG" distributor for sale with working dual diaphragm vacuum advance - as shown. $250.00 plus shipping from Houston, TX

Hey, I believe my rig is leaking a bit of oil where the distributor goes into the block. It's just metal on metal. Is there no gasket for this part? Thanks

After some help from the good folks on the forum, thought I would attempt a replacement of the internal seal and bearing Symptoms: Oil covered Alternator from the top LHS side of engine Oil dripping from the alternator housing Step 1. Remove Distributor Cap and observe if there is copious...

Hey all, I've been rebuilding my engine, and while the parts were at the machine shop I started work on the carb and dizzy, rebuilding the carb, and following the 'poor-man's recurve' linked here. After I got the dizzy apart, I noticed the shaft bearing didn't spin smoothly, and was audibly...

Hello everybody, I was searching about this over the forum but since I have a non US distributor (and cruiser), I decided to give it a try and ask. Sorry but no part numbers stamped on the distributor, the rotor or the cap, I suspect cap and rotor are not OEM and will look to replace them as...

Came as a spare with my truck I just bought and appears to be super clean low wear but I have no way to test... so assume its just for parts or rebuild? Unknown mileage as well but is for my 1993 FJ with the 1Z-FE. I have a few items for sale in other threads, price listed plus shipping: - NEW...

Hey guys. Old distributor went out so I ordered a new one. I set it to fire on TDC compression stroke. According to my timing light, it's getting inconsistent spark. Why could this be? I believe power to the distributor is constant. Thanks for any help!

Hi everyone! I picked up my first 40 a few months ago, a 1964 with a three on the floor transmission and a 1969 engine which the PO put in. I am very happy with it so far and am enjoying the project; however, I have encountered an issue that I cannot seem to solve. The truck idles beautifully...

Looking for an HEI distributor for my FJ40 asap. My daily driver's seemed to go out. 5/73 model. Thanks

Hey guys, anyone understand HEI style distributors? I'm running one of those internal-coil distributors the PO installed. Basically the motor died while driving. Got it home, here's the conclusion. The spark plugs are getting intermittent spark. It won't stay running because it cuts out and...

Having issues getting my 1985 FJ60 to start. I had problems in 2019 with spongy breaks so I replaced the brake booster in Sept that year with great results. I was driving it weekly and then one day in Oct 2019 it just wouldn't start. I wasn't getting a spark and due to work and other...

Good day everyone! We are mid-move and I've decided to list a few parts that I'd rather not have packed. All are Denver/Aurora area pick-up. You can come inspect for yourself. These parts were included when I purchased my '76 FJ40. As told, they were either spare parts or parts the previous...

Hey y’all! I’m in need of someone smarter than I when it comes to early efi on the 22re. My 85 4Runner will only run on the cold start injector, then dies. New fuel pump, starter, efi relay, open circuit relay, and grounds cleaned or replaced. Any input on where to look? Got it to pop code 10...

Hey All, I am trying to get my FJ60 air tight (Proven to be a headache and a half) and think I have finally done it. I hooked up my smoke tester and all seals seem to be doing their jobs. But, when I crank over the engine and get it up to temp, I am only seeing 14 inHG on the intake manifold...

From a 97 lx450 I'm selling a good working used distributor. I'd recommend replacing the o-ring that always seems to leak on these. Also replace the cap and rotor at the same time. 85 shipped to us I have other parts from a parts truck, anything that fits in the medium flat rate box will...

Hello everyone. I was wondering if anyone knows of another source other than cruiserparts.net who offers OEM rebuilt distributor for the 4.2 liter 6 cylinder engine? I've tried all my local parts distributors (Napa, O'Reilly, Autozone, etc with no luck and none available). My current...