crank

I removed the dash to do evaporator and heater core. After I reconnected everything the engine won't turn over. Any suggestions?

Notcing my FJ60 2F crank pulley has a slight wobble to it (newly rebuilt engine, just installed the crank pulley for the second time after recent rebuilt motor install) Is this amount of wobble normal? see video I also noticed the engine is sitting at a slight angle to the left, and am...

My recently acquired FJ60 (340k) suddenly won't start. Won't crank. Won't even click. Turn the key on, have power, turn to start...nothing. Tried jumping, no luck. Was previously making that low rah-rah-rah sound when cranking indicating either a dying battery or starter. After some...

Hi all, I am new to this forum but have loved what I have read thus far. Just a quick intro, I am based in Melbourne, Australia and have just purchased a 2019 Landcruiser Sahara (200 series. It’s my first cruiser so am super excited. Now my question if I may? I want to purchase an OBD2...

Took the ol girl out after having her setup for a bit, from working in her… when I got home I found a unidentified wire hanging from the wheel well… not sure if it’s related but the LC won’t even attempt to crank now… can someone tell me what it is and where it goes?

Anyone know of a good source for crankshaft bearings? Motor is a 5/73 1F. They keep getting put on back order. I'm hoping someone can point me to some that are in stock. Thank you!

My daughter has my 2000 LC100 at school (3.5 hours away). She called bc the 100 wouldn't start. On a video call, I can see/hear the following: No dash or interior lights working. No crank or clicking when trying to start. Battery read @ 12.5 volts. EFI Relay Bypass Kit Installed and 20 amp...

2004 Land Cruiser, will not crank. Battery good, horn blows, no sound from Starter Motor at all. Tried shifting in and out of Park, then Neutral, still no sound from Starter Motor. Before we have it towed to a shop to replace the Starter Motor I have a few questions: - is there a Fuse or Circuit...

It was already a sad day. I was at the card shop with my 4yr old getting some guidance on how much I could sell some of my old school Magic: The Gathering cards I’ve had since the mid 90s for. I was running pretty low on fuel so I filled all the way up at Chevron (my preferred fuel choice) on...

This came with my 65 fj45 which now has a 2uz in it, so this won’t do me any good. Original engine hand crank for a 1f. Asking $100 plus shipping. Located in Northern New Mexico. I will add picture’s shortly

Does anyone know the name/part number for the clear plastic washer that goes behind the window cranks? Im pretty sure I've seen them on toyota website when searching for screws, etc, but I have no idea what words to punch into Google to find them again. Thanks

Still working on my 10 year (so far) refresh project. If I connect both amp gauge wires together (bypassing the gauge) the motor fires right up. If I hook up the two wires to the gauge the motor will not crank and the amp gauge needle buries to discharge. The gauge also started to smoke...

Some advice needed, Car cranks but no spark, took dizzy cap off and cranked but the rotor wasn’t spinning, took the distributor out and it spins freely out and the gears look undamged. When the distributor is in I can’t turn it by hand. Will take the valve cover off tomorrow but any...

Oh man I’m in trouble. Harmonic balancer quit on me, and lost the #2 pulley about a month ago so truck has been parked for a minute. Replacement parts from megazip are a fit, but the replacement #2 pulley only has one belt groove which means i get no power steering. Anybody know whats up with...

Or if anyone has information on what might interchange. 90105-16003

Otramm crank holder tool for 1FZ-FE. Used once. $60 local pickup. $70 shipped USPS flat rate.

Here we go again.. 97 LX450 Very familiar with the fusible links, EFI fuse, EFI relay causing this. My situation: - Had issues with no CEL, crank, no start condition - was able to wiggle the fusible links and get it started - figured the fusible links were going out - replaced fusible links...

Greetings all! Had a little trouble with the GX today. Engine stalled on the freeway on the way home, got it pulled over and now... Crank no start. Pulled up Torque Pro, had a code for Crankshaft position sensor circuit A. I think... Haha. Stupid me, I thought I snapped a screen...

Just wanted to quickly post the results of post-mortem on my 3F-E: The missus drove my car while I was away interstate, made it 2 blocks away from home, car stalled, wouldn't start again. Dragged it home, wrenched for 5 days to no avail. Discovered cranking would turn the accessory pulley but...

Anybody have a crank start handle for an FJ40? The one that you stick in your crankshaft pulley nut to start the engine if the battery is dead. Thanks.