cooler

Seems we may have overbought with our Dometic CFX3 75DZ. Cooler has been great but is really overkill for what we need is is making it difficult to add the drawers with a fridge slide for our GX470. Looking to seel or trade for a similar featured 50-60l version from Dometic or ARB. Anyone...

No longer available

up grading our 67 restoration with a mini truck power steering conversion, boy those boxes are hard to find, just got one. We are using 33 inch tires, do we need a power steering cooler?

With the summer heat in full swing lately here in California I have been noticing my transmission temperatures go fairly high (monitored with Torque Pro, not towing). On level roads going about 30-40 mph I see 200 to 210 F (in D and 4) and over 220 to 240 F when going up mountain roads and good...

Has some cracks in the plastic and dings but cools like it should. It's around 20 years old and holds a 12 pack. I've never tried the freezer function. Comes with Aussie AC cord, DC cord and a small inverter for US AC. Been stored inside. Really don't want to ship it as it's heavy. $175

Does anyone have the following "J" pipe nut shown in the picture below?

I just spent a couple evenings working on my 1994 Land Cruiser. The power steering cooler had some pretty bad corrosion/rust that lead to a leak in the "paper clip" cooler. To help the next guy I wanted to let you know what all needs to done to replace the cooler with an OEM part or like me, a...

Looking for this hose that runs from the water pump to the oil cooler on '76 to '80 FJ40 with oil cooler. It's part 15777 in the diagram.

I just bought an ozark expedition 52 qt cooler at walmart. It's basically a Yeti rip-off, roto-mold cooler. I paid 147.00. It seems to be built to last a lifetime (kept out of the sun). While this seems pricy it is cheap compared to yeti at around 400.00. Looking at this site/thread Ozark...

There is a horizontal hose that attaches to the Oil Cooler. I want to replace it and was hoping someone could verify I found the correct one. It's a straight hose, no fancy turns. OEM Hose for 1988 Toyota Land Cruiser|90445-18085 : Toyota Parts Online | Olathe Toyota Parts Center I realize the...

Anyone else had this happen? The lower barb on my at cooler is almost corroded through. The top one looks completely fine. Is there a drop in new replacement that anyone has used instead of the oem? @beno whats a new one of these cost?

I just hit about 80,000miles on my 2010 cruiser and want to do a ATF change. Im looking up parts at grapevine toyota and other places I usually order from and they have two options for the pan. One with and one without a LC oil cooler. Its a non us version LC. Here is my VIN JTMHT06JXA6062361...

Looking for stock FJ40 Power Steering cooler for 1979-1983. I have everything else but this.

I purchased this oil cooler and downward facing oil filter housing combo anticipating a turbo on my 3B from a wrecker off the shelf hence an unknown 3B or B series engine variant. Can anyone tell me what it is from?? and why it seems to be missing the oil lines to the vacuum pump on the back of...

Finishing up new radiator install. I have one of the cooler lines between the frame rail and bottom of the radiator. Are both lines supposed to be together routed outside/in front of the radiator? Not much room, and my memory didn't take note when I pulled the old rad out. Pic 1 shows the line...

I'm looking for the front two lines (soft lines) that connect to the radiator. They are discontinued by Toyota and my local shop can't make them so I'm stuck looking for a good used set. Anyone have any? Thanks

Truck is a '94 fzj-80 U.S spec. So I was doing a little inspecting around my truck and figuring out routing of hoses and such just to get more familiar with things...Take a look at the below photos: Both lines from the trans cooler look like they've been cut!? Return and sending line...

The paper clip is rusted pretty bad and leaking so the time has come. Going to go with the Derale Dual pass cooler mounted to the frame. This is the model I am going to go with: Amazon.com: Derale 13263 Dual Pass Aluminum Heat Sink Cooler: Automotive I want to eliminate the metal bends on...

Does anyone know the fitting size of the transmission cooler hardlines on the FJ62? They are bigger than the 14mm fittings that go into the radiator. Trying to finish up my aux cooler install and Want to order the correct AN- fitting adapter. Thanks for any help!

I'd like to add an oil cooler to a 2F. The factory setups seem to be uncommon and on the expensive side (compared to a cooler I already have) since the oil tap at the filter is pressurized. Am I looking in the wrong place (ebay)? Is there an easy way to tap into the unpressurized side of the...