carb

I’m not sure if this hissing (aka air spewing) is normal coming from the jet in the primary Venturi … I took off my air cleaner assembly to look - just sounds really loud. And maybe my ears all the sudden are just attuned to it or it’s new which I think. I was attempting to tune the carb a bit...

I’m using an A/F ratio gauge to help me get my carb jetting dialed in. I’m lean at both idle and cruising, which I expected, since I have a hotter than stock cam, and more free flowing exhaust. Quick question on idle circuit and main jets. Does the main jet affect the amount of fuel going to...

Hey fellas, Installed this chinese carb on my newly rebuilt 2f, and after running the 2f/break in its apparently started to leak -- fuel. The sight window didn't show gas up to the level like i've seen this carb properly do befoore. Wondering what's going on here and the fix --- and most...

We have a section of timber, far northwest, these two orphans were here and part of the deal, rose bush and packrat nest included. No huge attachment, not yet sure what I'll do with them, just wanted folks to know they are still out there. The little black one is a '78, also 4 on the floor, and...

Bought a motor with this carb on it. I have seen it run but never drove it before pulling the motor. $ 125 + shipping. Updated the price.

So I have a 69 FJ40 with a SBC 350, 400 trans, electric fuel pump. I have been thinking about going to a qjet carb, 750 cfm. Or, do I bit the bullet and do a Sniper II EFI? I would like to drive this a few times a week around town and to and from work. Any info and/or advice, good or bad...

According to the stamps, this is an OEM Aisin carb from a ‘84 fj60. Date of mfg is March 13, 1984. It came from my running '76 FJ40, and the PO had it installed when he had the engine rebuilt not long before I bought it. When I restored my truck, I went with an EFI setup. Comes with a spacer...

I've so far been unable to get my secondary to open.. I rebuilt my carb ~1,500 miles ago, did a good job, made sure all the vacuum passageways were open, and of course installed a new secondary diaphragm. However, I found that the secondary was not opening beyond the minor amount initiated by...

Ive got a 1992 FZJ80, it's got a trash aftermarket carb on it that needs replacing and it's nearly impossible to find the part which I'm advised the VIN calls for (21100-66030 or 21100-66031). The only original carb I could find is the (21100-66012), which I ordered from Dubai on ebay...with my...

I swapped the Holley marine carb the PO put on for the original rebuilt carb. I started with the idle mixture screw 1.5 turns out. I'm at 6.5 turns and and that seems pretty far out. Is is this normal? I haven't touched the high idle yet and don't think I need to until I have a low idle...

Hello- just joined this group. Need help. Fellow gave me two weber carbs. They were on english sports car. How do I Identify the model number and determine if either of these will work on an fj40? Thanks in advance for the help. Bill

Hello gents, In resurrecting this FJ60 from storage of a friend in a barn for 11 years. Overall its great, but NOT definitely a daily driver yet. Some background. It drove great in the morning, it drove great in the afternoon. It did not drive great in the morning and the afternoon! So I'm...

Aisin carb from a ‘75. Just a rebuildable core, but I think it’s all there (someone please correct me on that if that’s incorrect). Located in southern middle TN. $75, obo, plus shipping. I have never used this carb, it was just in boxes of parts that came with my 40 when I bought it years ago...

Need some help. I decided to replace the Weber that was on my 86 FJ60 with a Jim C rebuild. Luckily I had all the linkage and choke cable still. I made sure to double check the desmog doc to make sure there is nothing missing before putting the OEM on. Unfortunately, what once was a...

A while back I read a post where someone had a carb fan fix using off the shelf parts to replace the carb fan sensor and thermostat. I purchased the parts and stowed them in a box for "later". Now that I want to install them I can't find the post. Tried searching any carb fan posts I could find...

Complete manifold temp sender assembly. Pulled from a ‘79 2F manifold but fits 77-87 2F with carb cooling fan. $55 shipped

I’m currently working on 75 carb I recently picked up and installing the return line and wanted to know where the opposite end of the line rests where it mates to the soft line. Mine currently is right up against the battery and would like pictures so I know where I need to bend it if needed...

Does anyone have experience removing the carb heat shield from the intake manifold...it looks like the insulator block is glued to the manifold

I have an FJ62 88, 200k miles, body in great shape, but recent rebuild didn’t go well. I want to overhaul to make is a daily driver with highway speed, something to last for the next 20+ years. The Mosley high power rebuild seems ideal, but they are booked up...

Aisin carb dated as the correct model for the year(1972) based on the SOR site. Recently rebuilt. after a few fixes, I thought I would attempt to fine tune things. Was planning on doing a lean drop idle adjustment but when I attempted to use the mixture screw it had no effect on the idle speed...