bearing

Hi all, Hoping to get some guidance. I have 19 Premium, 37,000 miles which has been diagnosed with a left rear bearing failure by the dealer. I've been chasing this one a while.. Humming noise starting around 30, gets worse at 40 and up. Since the car is Certified Pre Owned, I took it to the...

Hi All Just noticed that there is a hell of a rattle coming from this area on my high mileage lx470. What it sounds like is a thrust bearing but this being an auto .... Anyone have any experience with this as a common point of failure?

Long time lurker here. 99 with 303k miles. Running an Ironman stage 2 lift with the diff drop, KO2 285s. I have a hum or could even call it a growl that’s most noticeable at 40mph+. Becomes higher pitched with increased speed, and lower pitch/ louder during deceleration. Braking has no affect...

Hey mud, 1600 miles into a 3500 mile road trip and I think we spun a wheel bearing. Cold morning in Yellowstone and in an instant a chugging/wub wub wub came from front driver wheel. Became a higher frequency at highway speed. However, no steering shake and 6/12 wiggle was fine. Pulled the...

Finally getting around to prepping my f155 engine for reassembly after it sat for a couple of years in the work trailer. Just got around to test fitting some parts and plasti-gaging the crank with the new bearings. With the main bearing cap shims, the oil clearance is around .07mm, barely...

M040a main bearing set for 84-up 3B engine. $35+shipping

Hi all I just did my rear main seal and followed @Poser ‘s method, which is taking the oil pan off along with the main bearing cap (#4). My engine is a ‘77 2F, and I have it off the vehicle on an engine stand. Overall it went very smoothly. When putting the main bearing cap back on, what is...

Hi all, First post from a new member. New to me 2006 GX470 cv axle has a loose connection at the input to the front differential. I had thought this would be an opportunity to upgrade to a bushing but a bit a question to ECGS revealed to me that these rigs do not use the pesky needle...

So I ordered these a few months ago from Mag Engines in Dubai. Very attractive price, maybe now I know why. The tabs for half the shells are on the wrong side... And the set doesn't include the #3 thrust bearing. 😐

Had a lot harder time on my drivers side than passenger side with rust when doing the tear down for front wheel bearings. Looks like the brake dust shield plastic shoulder has separated from the metal neck. I’m thinking water is getting in and living there and rusting everything. Logical...

Ok so I have a issue at hand. -------- Solved - Turned out to be a bad Caliper piston that was rubbing on the rotor. I replaced the rear rotors, pads on both wheels, did a little bit of brake bleeding. That fixed the problem. I did put in a brake noise shim this time so I know if my brakes pads...

I've recently returned from a trip through the WA mid-west, nothing too rough, bit of gravel is all, and towing our offroad van (under 2000kg). I had been back for a couple of days took a drive for coffee (12km at 60kmh) and could smell hot metal from the passenger rear wheel hub. Drove home...

What kind of grease (if any) do you use here?

I have an ‘81 BJ42 with a 13B. I believe I need to replace the main bearings but I need guidance how to identify the main bearing specs for correct replacement as well as where to locate preferably OEM main bearing replacements. I don’t know the month or year of the engine. Here are some...

I’m in the process of changing my oil pan, and I faintly noticed tiny metal shavings in the pan that did not appear in the oil change. You can also see sludge and a little bit of coolant residue that was from a bad oil cooler gasket which I replaced already. My issue is not knowing what to do. I...

Has anyone else suffered complete bearing failure on their 4X4Labs rear bumper swing out? Discovered my spare tire swing out was super loose after a trip. Eventually accessed the spindle with a lot of hammering and screw driver prying. Turns out the bearing rollers turned completely into sludge...

Hi, Can anyone confirm these are the correct bearings for the rear axle on a 1991 PZJ77-MNS? 2 x 90365-47013 Partsouq also gives a Koyo equivalent as being RNU0727 but they don't stock it at the moment. This is a semi floating axle so am I correct in thinking that I should also expect to have...

I've looked all over and haven't been able to find anything conclusive, so I thought I would just make a post to ask the question and establish a concrete answer. When I look online at rear axle seals and bearings they appear to be split into pre-73 and post-73 packages. Reading online the...

Hi guys, Does anybody can tell me the Size of the inner and outer pinion bearing and oil seal of a bj73 fullfloater rear diff? Thnx a lot for your help! Grz from holland

Noticed some sludge coming from the wheel nuts a few days ago. Thinking I have a bad inner axle seal. Here's the writeup from a local shop: "Your front diff fluid is contaminated with knuckle grease due to the bad inner axle seals and has turned into a nasty mud. It is going to require...