I have two 24 volt 3B’s for sale in Wilmington NC. One has a crankshaft that has blown apart and the other started to knock from the bottom end. I can take individual parts off if anyone is looking for something in particular.
$700 for the one with a blown up crank.
Has a newish head on it...
My old 3B blew up and I got a new one, although it has higher Kms. My old 3B had the injectors rebuilt 60k miles ago so i figured I'd go ahead and swap them but they don't look nearly as good as the ones I pulled out of my new engine. I don't know much about injectors/how to tell when one is...
Description:
B , 3B, 11B & 14B Engine Repair Manuel
Condition:
Appears that some liquid spelled on it long time ago but it’s in good condition & complete papers
Price:
$300.00
Shipping:
$34.00
Payment:
PayPal
Located in Calgary, Prefer local sale can be heard running both are 24 volt, too heavy to ship, left hand drive Canadian Spec engines
1982 BJ42 parts for sale aprox 300000 km
3B engine new water pump, stock, complete
H42 4 speed transmission with split case transfer case
24 volt...
Hi,
tried to found some info online but wasn't able to found anything related to my issue. Bought a 3b/h55f combo from a hj70, engine as been rebuilt, clutch is new and flywheel as been resurfaced. Everything works well beside a grinding and vibration on 3rd gear. I'm aware that the 3rd synchro...
Hey there I have a 1987 BJ75 Troopy that has a turbo'd 3B in it, about a week ago going up a hill in 2nd gear my engine started to lag, like majorly lag. I lost boost pretty fast, went from 18psi to 7psi in a matter of moments, pulled over to the side of the road checked my oil, turbo, and...
About a month and a half ago I graduated high school and left to travel across the country with 5 other friends in my 1987 BJ75 Troopcarrier that I had just slapped a $50 junkyard turbo onto 3 weeks prior... No power steering, no air conditioning, no lumbar support, and no horsepower. I'll just...
Anyone out there have a old 3b core they wanna part with I need a 85 to 87 with the 5 bearing cam. Threw a rod and cracked the block, got a core for rebuilding and the machine shop took 3 Months to.tell me the block was NFG. So i have a full kit for the engine sleeves and all. Just need the engin
Hey there, I'm trying to save as much money as possible on my turbo setup and was wondering if anyone had a CAD file of a 3B exhaust manifold flange as shown in the picture below. There were a lot of people posting links to them back in 2010-2012 but since that was 10 years ago all the links...
About a year ago when I was adjusting the valves on my 3B and being inexperienced etc etc, I over-torqued the valve cover which caused a fracture, which slowly leaked oil out of it (not an amount that would change your oil level, just made the valve cover look nasty in that certain area). Thus I...
So I’ve tried almost everything I’ve read on Mud. Still no luck. 84 3B 60 series. EDIC cycles every 10 seconds with accessories on (heater, lights, etc) doesn’t stall engine, just cuts fuel for a split second
Cleaned all grounds throughly
Replaced oil sender for gauge / Cleaned wire for oil...
G'day everyone,
I have here a rotary injector pump off a 3B up for sale.
Part no. 22100-55201
Located NSW Australia. Can ship at buyers expense.
Looking at $750 Aud for injector pump. Can also add fuel lines and old injectors if needed for an extra $100 Aud.
Ran perfectly when it came off no...
Hey there, I recently installed an EGT gauge all went well... I think, but I think like my temps are too low from everything else I've read online. It stays between 400-600 degrees Fahrenheit at all time pretty much, I was able to hit 700 for a couple of seconds when I ran it really hard from a...
Alright. I had this issue once before on my 86 BJ60 - 3B, And i solved it by cleaning the ground between my frame and bell housing. However, now my EDIC keeps cycling to stop for a split second and then back to run. At idle with no accessories on, it seems to happen rarely. It persists more when...
Hey there, I recently got an Issopro EV2 EGT gauge for Christmas and was wondering where the best place to put it would be for accuracy and response time? The 2 places I'm deciding against I have marked in red and orange as you can see. So which would be better, or is there another better place...
Hey there, around the start of August my glow plug timing started acting up, I could hear them go on and then back off almost immediately, yet the glow plug light would stay on for how long they would usually be on for. Then after a week, they started working normally again and would turn off...
Hey guys, I recently purchased a BJ60 with 260k kilometers on it and I am a new member of the community. I posted under the 60 wagon thread already and they told me that I could get more responses here. As I drove it back from Ohio I noticed the engine hesitates on acceleration when I turn on...
I am at a cross roads as many people before me. Over the past few years I have accumulated parts and cruisers to build one from the ground up the way/condition I wanted one. But I severely underestimated the time needed to raise a newborn and maintain a house. I managed with kid one but now with...
I have a power steering pump for a 3B engine. Might fit other vehicles, too. Very clean.
I bought it from another MUD member a while ago. Asking $100 shipped.
-Alberto