Recent content by 87nm60

  1. 87nm60

    Charcoal Canister Operation?

    Curious if you ever found a solution? I was out in mine on Sunday and ran into the exact same issue- stalled at a red light after being on throttle. When I got home and turned off the truck, I could hear an audible "whoosh" coming from the gas cap. When I unscrewed it, it almost shot off into my...
  2. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    I went into Autozone this time around and sure enough, they had the 3/8-16 1/2. Nice and easy. Next time, I’ll go there first instead of Ace.
  3. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    Curious where you found your bolt? I didn’t see anything 1/2 at Ace. The 3/8-16 started at 3/4 and went up from there.
  4. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    Hot off the presses! This is the 1/2 bolt I found at ACE. After tightening down, you can see how far in that threaded hole this little sucker goes. Not sure if this is going to seal these holes up or not? ACE didn’t have a 3/8 16 1/2 bolt with a head so I rolled the dice and bought these hoping...
  5. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    Curious what everyone is using to plug the two threaded holes on the back of your pumps that come with a green and red temp plug in them? I found some 3/8-16 1/2 studs at Ace but when I went to install, it went into the threaded hole further than expected. By the time I tightened it down, it was...
  6. 87nm60

    Top heater nipple fj60 2F

    I’m looking to understand if that shutoff valve actually works on a 60? I bought one and installed it (haven’t fired up the motor yet). Matt, you left a comment on your Instagram post for this and said it would not work for a 60. So now I’m confused? Do I need the simple union with no valve...
  7. 87nm60

    Oil change intervals with synthetic oil?

    This is just overkill. 2500-3000? You’re wasting a lot of money and time.
  8. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    Glad you posted this. I saw the o ring in my pump box and wondered what it was for. Like you said, these fittings don’t usually have them. I’ll need to go back and install.
  9. 87nm60

    Remflex gasket torque on exhaust headers

    any updates?
  10. 87nm60

    Finally!!!! Saginaw PS pump conversion kit for FJ60s!!!!!

    I am working through putting my 60 back together and have come to the power steering portion of the project. I bought this kit and have been thrilled with it so far. I do have a couple of questions I'm hoping someone can help me answer. I read through the thread multiple times and didn't see an...
  11. 87nm60

    Front doors rattling from speakers

    Same issue here on my 05 LC. Since I owned it, I’ve always chalked it up to a bad door speaker. Well, I just replaced all the door speakers and the noise is still there. 🫤. After pulling the panel again, I believe it’s coming from the actual door speaker cover. The cloth seems a tiny bit loose...
  12. 87nm60

    Misc Torque Specs - Use at your own risk! (FAQ)

    Curious… anyone know the difference between flywheel bolts and fasteners? I take it fasteners are the bolts that mount the flywheel to the crank and should be torqued between 58-79 ftlbs… Flywheel Retaining Fasteners 58-79 foot pounds Flywheel Bolts 47-51lbs (FSM)
  13. 87nm60

    Door Lock Actuator Replacement

    Yep. Looks like you got the collared version and not the d shaft maybe? I just did my drivers side door yesterday. It was a PITA. I did it without removing the entire actuator. Reason being… I couldn’t get the rods out of the door handle! I tried for over an hour. But… after getting the actuator...
  14. 87nm60

    Door Lock Actuator Replacement

    Thought I would contribute to the thread since I’ve found it so helpful in fixing my locks. I’ve got a 2005 LC and it runs the d shaft without the collar.
  15. 87nm60

    2005 Landcruiser Steering Pop

    Thanks. I agree. I just received my order from SuperPro and will be scheduling an appointment with my mechanic to get them installed. I’ll report back once that’s done to let you know if it fixed it or not. Hoping so.
Back
Top Bottom