Window channel gasket......

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 8, 2013
Threads
282
Messages
1,476
Location
North GA
Received my DS and PS plastic window channel gaskets in today. I've been trying like hell to chase down a mysterious water leak into the bottom of my floorboard near the edge of the door. Since my existing plastic is peeled up and the white clips are all broken I've suspected this could be the culprit.

Has anyone had a similar leak?
 
Sunroof drain channel?
 
Windshield is another potential culptit.
 
I sprayed the windshield with a high pressure hose looking for leaks....nothing.

Sunroof drain down the pillar maybe? I was thinking water into the door from the broken weather gaskets and out the bottom.
 
Trying to track a similar leak. Sunroof is siliconed shut. Just replaced the front windshield per fsm and seems to be glued tight.
 
Had a windshield repair guy look at mine the other day and he said the windshield uses a gasket and not any glue. That was a first hearing that for me. I know the windshield was replaced by PO. I suspected the WAS but can't visibly see any leaks. Wondering if its leaking and flowing down inside somewhere and into the floorboard!?
 
Had a windshield repair guy look at mine the other day and he said the windshield uses a gasket and not any glue. That was a first hearing that for me. I know the windshield was replaced by PO. I suspected the WAS but can't visibly see any leaks. Wondering if its leaking and flowing down inside somewhere and into the floorboard!?
For sure. And the FSM calls for glue on both sides. Mine was physically cracks causing the leak. I went through the FSM with the installer and left him the printed pages on correct install for these trucks.
 
Had a windshield repair guy look at mine the other day and he said the windshield uses a gasket and not any glue. That was a first hearing that for me. I know the windshield was replaced by PO. I suspected the WAS but can't visibly see any leaks. Wondering if its leaking and flowing down inside somewhere and into the floorboard!?
Definitely should glue both sides of the gasket. If there is no glue on yours, that's my guess for the source of the leak. Does your windshield squeak when going over bumps?
 
It doesn't squeak.....and I don't see any water residue around the edges. Makes me think its leaking down inside and out the bottom into the floorboard somehow.
 
Pull your kickpanels and look for water runs if you suspect windshield. That would indicate failure between gasket and body. If you see puddles in inside corners the glue has failed between glass and gasket.

Is this the guy in the walmart parking lot under an ez up? Lol

Your dude was plain wrong. FSM even specifies so. Took me 4 shops to find someone willing to follow the fsm and not ASSume they were right.
 
It doesn't squeak.....and I don't see any water residue around the edges. Makes me think its leaking down inside and out the bottom into the floorboard somehow.
That's exactly how it does it. Usually pools into the corner of the gasket and leaks down the corner of the cab right behind the kick pannel area and under or onto the carpet pad.
 
Definitely should glue both sides of the gasket. If there is no glue on yours, that's my guess for the source of the leak. Does your windshield squeak when going over bumps?
Mine squeaks like crazy. I thought that was normal. Does anyone know how much the glass guy would charge to reinstall the gasket correctly?
 
The windshield must be installed using the correct adhesive-sealant, or it will leak. Many discussions on that topic.
One source of a leak just inside a door is a missing or damaged vapor barrier behind the door panel/card.
 
They guy told me the windshield would more than likely break now if you tried to remove and reinstall etc. But he also said it didn't use any glue so there you go :doh:
 
Front windshields are pretty cheap ..$296.00 installed from Safelite. I suspected my windshield gasket was leaking..the gasket was dry and it was original glass. Guy came to my house and glued the gasket. No more leaks and even better the new glass is UV and has the dark tint band across the top. My original glass was pitted due to age but the heat one felt driving into the sun was also intense. The new windshield solved that and the service i experienced was top notched. I also had them replace the rear hatch glass at the same time because the defroster stopped working.
 
They guy told me the windshield would more than likely break now if you tried to remove and reinstall etc. But he also said it didn't use any glue so there you go :doh:
They cut the windshield gasket and the glass came right out.
 
Mine squeaks like crazy. I thought that was normal. Does anyone know how much the glass guy would charge to reinstall the gasket correctly?

Pretty sure theres gonna be a range difference between holly springs and LA ;)

I posted the local shops cost in the ONSC wrenching thread. 150 in my area but id call around your town for an accurate estimate. It took a few shops to find one willing to follow fsm. Heres a thread with some rdu sources

Reputable Windshield Guys for 80 Series

If the gasket was glued and its just failed they likely wont reuse gasket with old adhesive present.

For a temp fix tou could follow firetruck41's write up but not sure it will fix the squeak. More for stopping a leak.

My squeak was so bad there was no way i was going to utah for a month listening to that. Since it was leaking too it was time. New gasket from beno and glass from the shop that did the work.
 
Last edited:
Back
Top Bottom