What have you done to your Land Cruiser this week? (152 Viewers)

[ToyotaMatt]

 

[ToyotaMatt]

 

[aging fleet]

Wrapped up months of work so I finally got it out and drove it. Smiles for miles.

 

[EmanC]

Took an idea from @77CruiserDog build and added these Energy Suspension- 9.9103G to the bumper. $13 bucks shipped and look great in my eyes. Just had to add a washer, lock washer, and normal nut as the included nylock was a bit of a pain to get tightened.

​

 

[brooklyn]

Purchased some parts Toyotapartsdeal.com…

 

[brooklyn]

Almost added this to the heard, but some fatal flaws for the price - backseat access worse than any two door I ever owned & front seats really sit low — strange design really!!! All the sales guy wanted to talk about was my 67 FJ40

 

[Green Bean]

Under the category of "It is the Tiny Things": 3d printed compass module cover inside glove box for Dakota Digital module.

 

[EmanC]

Made some custom 73 style knobs.

 

[mechanyx]

Made some custom 73 style knobs.

That's very cool! 3D printed? If so, what type of filament do you use?

 

[Jackson Hanes]

That's very cool! 3D printed? If so, what type of filament do you use?

They almost look like they were printed on a resin printer, not a FDM.
Probably was though.

 

[EmanC]

That's very cool! 3D printed? If so, what type of filament do you use?

3D Printed, but on a Resin Printer. So much higher resolution than traditional FDM style printers.

Also did a few early style knobs/

 

[deliverance]

Replaced the three groove balancer with a two groove I had on a spare 2f. The balancer had a nasty wobble and ate thru the speedy sleeve, causing a massive oil leak. No leak so far and the replacement is much straighter.

 

[77CruiserDog]

Took an idea from @77CruiserDog build and added these Energy Suspension- 9.9103G to the bumper. $13 bucks shipped and look great in my eyes. Just had to add a washer, lock washer, and normal nut as the included nylock was a bit of a pain to get tightened.

​

View attachment 3007940

Looks awesome man!!

 

[SergP]

time for ambulance door ....

..one more to go...

 

[Bripars40]

Worked on a fan shroud for my 2uz swap. Had to offset it a little too since it was within a 1/2” of the old fan pulley.

Wish I had left enough room for a mechanical fan, but hindsight is 20/20.

 

[Ackcruisers]

Started a complete fuel system overhaul. The plastic tank is out and ready to install OEM factory tank with new fuel lines and pump. Adding a late model pump with fuel return line.

 

[Flatlanderfj40]

Coffee in KC

 

[Skreddy]

Put my new cityracer cowl vent gasket on and finally drilled the broken screws to put the cover back on.

 

[ceylonfj40nut]

3D Printed, but on a Resin Printer. So much higher resolution than traditional FDM style printers.

Also did a few early style knobs/

Worked on a fan shroud for my 2uz swap. Had to offset it a little too since it was within a 1/2” of the old fan pulley.

Wished I had left enough room for a mechanical fan, but hindsight is 20/20.

View attachment 3009662

Is this a Volvo fan? Two speed?

 

[Bripars40]

Is this a Volvo fan? Two speed?

Yessir, out of a s70 with the relay system as well. Here’s a link to more info

Volvo Electric Cooling Fan

www.therangerstation.com