I finally went and bought the Sequoia/Tundra wheels from @FastCarGuy Bob is a great guy and has a great looking rig. Now onto finding the proper lugs, wheel spacers, and save up for those 37x12.5x17 KM3.
What Did You Do with Your 80 This Weekend? (102 Viewers)
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
94trilocked
Supporting Vendor
A couple weeks ago I had to move a bunch of woodworking stuff I had inherited... a ridgid 3650 table saw, old craftsman jointer, lathe, associated stands/bases, handtools, some nice wood, etc. Took out all the rear seats. Everything fit for the 700 mi drive home... I shoulda took a pic!
96LandcruiserPJ
SILVER Star
I feel you - If we don't go somewhere tomorrow, Ill be epoxy-ing some loose bits and running it around the block to see if I did it right.
I am getting the Cruiser ready for quite a long trip. So I did an oil change, cleaned and vacuumed the whole thing, replaced the rubber seals on one headlight, checked the birf grease, the nuts, and replaced the driver wiper arm.
But when I was looking at the arm, why shouldn't I just replace the spring with one off McMaster? The arm is $60+ (100 from the dealer). A spring would be like $7 for a 3 pack.
But when I was looking at the arm, why shouldn't I just replace the spring with one off McMaster? The arm is $60+ (100 from the dealer). A spring would be like $7 for a 3 pack.
Last edited:
Cruiser lost some more weight. I had new toyota plugs and wires so while I was in there I deleted the egr,split the intake and got rid of all of the vacuum stuff. I ordered the wrong "keychain" so I had to make a temp for the intake. Surgery went well so far.
Finished painting and reinstalling my flares. Think I’m going to paint the door trim strips the same too. Thoughts?
Nice! who makes it?
Bought life jackets in case of a snorkel failure.
Trying to organize with the addition of Dometic CFX50. These really need a slider to make it more accessible. Oh...(And don't you all dare laugh!) made an arm rest...it's really awesome...really!! 
Went to the Home Despot to get wood but as usual I roamed around and got to thinking...etc. etc.
Went to the Home Despot to get wood but as usual I roamed around and got to thinking...etc. etc.
malteserunner
Dr Evil
Went to a Boys & Girls Club car wash fundraiser.
Look at all that dirt!
Look at all that dirt!
MoJ
Moderator
@ Ale-8 
I'm chasing down a cylinder 5 misfire. Compression was great. Got spark. Checked fuel injector @the harness with a noid light and got nothin. So I get to RIP open the harness and find out why this one injector isn't getting power/completing ground. I also cleaned it inside and out. I got it yesterday for 600 bucks.
94trilocked
Supporting Vendor
Woot! I did All The Things!
Ghetto fab'd a "cargo barrier" from some cargo netting remnant to keep Milo in the back, since his crate doesn't fit now with the drawer system in . I have plans to create a wire mesh cargo barrier/sleeping platform extension, but this will do until then.
Picked up my first 80 yesterday. Loved my first 2 60's so excited about this '92. Got a good deal and the a/c even works! After a couple American v8's I'm back to slow and low 
Avid Off-road
Picked up my first 80 yesterday. Loved my first 2 60's so excited about this '92. Got a good deal and the a/c even works! After a couple American v8's I'm back to slow and low
View attachment 2010627
View attachment 2010628
View attachment 2010629
View attachment 2010630
View attachment 2010631
Colorado plates but Texas stickers on the windshield ?
Painted wheels for my 97. Hoping to install them tomorrow.
