Water Pump Woes

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Orange Hat

SILVER Star
Joined
Dec 14, 2017
Threads
17
Messages
199
Location
North TX
Well, wouldn't you know it...the day before I plan to take the 80 in for a state inspection, the water pump crapped out on me when I pulled into the office this morning (coolant all over the parking garage floor)! I'm about 25 miles from the house so my plan is to fill the radiator up as well as the overflow tank with distilled water and take off towards home. Based on the dummy temp gauge (I don't have a ScanGauge), I was going to stop a 1/3 or 1/2 of the way to allow it to cool down, top off with water, and then keep on rolling home. Does this sound like a good plan or am I asking for trouble?

The frustrating part of this, and to add context/color, was that I was planning on a full coolant rebuild (new hoses, rear heater delete, Ron Davis radiator, etc) after I got the inspection/registration renewed online so I didn't have to physically go into the DMV (I absolutely hate standing in line for hours at the DMV!). I'm wondering whether I should throw a cheap pump on it, top off fluids, go get the inspection, and then prepare for a coordinated and timed teardown...decisions, decisions!
 
I'm wondering whether I should throw a cheap pump on it, top off fluids, go get the inspection, and then prepare for a coordinated and timed teardown...decisions, decisions!

^^^^^

That's what I'd do. Give you time to collect all your parts and to do the job at a time of your choosing.
 
Personally I wouldn’t do that. Mine did the same, started leaking and noisier than normal. I pulled over to a gas station and called work which was only a mile away and told them I was going to take it home (6 miles) and then have my wife drop me off. Got about a mile out and the water pump seized up completely. Smoking belts, fluid leaking, etc. I ended up having to get a flat bed to take it to my place.
 
If its dumping coolant that bad, I would not drive it. Tow it home or bite the bullet and have a local shop replace just the pump. I've learned this lesson the hard way - a few times. :)
 
Great advice all...too much risk on tearing something up more. I went on and left it at work and will get it moved to the house this weekend with the 200 when traffic is light. I probably will still throw a cheap pump on it to buy some time so that I can get everything buttoned up the way I want.

Thanks...fantastic community!
 
Does your Auto insurance include towing? Recently had to flat bed one of my
80's, easy peezy, nothing out of pocket.

RockAuto, Aisin brand water pump, less than $70 shipped, identical to the Toyota part, comes with the gasket and studs:


Same here when the PHH blew out. Free AAA tow. I think I get three 100-mile tows a year if I need 'em. So far it's 4 miles once. But holy crap--you know what a slidebed costs? My pre-Cruiser SUV was towed maybe 3-5 miles, invoice said $350. (Insurance paid.)
 
X2 on AAA
 
X3 on AAA
 
Great stuff all! Let me check with my insurance, never even thought of that...would definitely be easier that way.
 
If you don't have towing coverage IME it doesn't cost much to add it to your auto policy. Or AAA as mentioned above.
 
My mistake, since I upgraded to gold, I think I get six 100 Mile tows.
 
Just an update that I got the 80 home...used my 200 and a $50 U-Haul trailer (no dice on insurance).

1ErjIZ2.png


It's in the garage now awaiting a promised full teardown of the coolant system!
 
Ok all, time for some more collective wisdom!

I finally was able to get around to tearing into the 80 today...water pump is off as well as the thermostat and all hoses. Now my goal was to pull and replace the radiator while I "was in there" but it appears to be in much better shape than expected. Now I know this is subjective, but I'm assuming it must have been replaced at some time over the life of 244k miles because it "looked clean"...ie, there isn't much rust, dirt, grime, etc like the rest of the vehicle. There is also some scaring on the fan side of the radiator that looks to have been caused by installation at some point I'm assuming. So with all that said, here comes the million dollar questions...

(A) - Leave the radiator in and alone? It's already drained so not sure if a flush would do anything.

(B) - Remove radiator and take to a radiator shop to have them work whatever magic on it?

(C) - Remove, throw it away, and replace with a Ron Davis as planned?


Again, option C was my answer before going into this but honestly, the Discontinued Parts Thread is so depressing that I'm not sure how much "extra" money I want to put into it.
 
I'd leave the radiator in

or get a brand new TYC radiator off Amazon - at ~$130, it is much cheaper than a Ron Davis, no fitment issues, and Arizona dry-heat-furnace tested by several of us :cheers:
 
Last edited:
I'd leave the radiator in

or get a brand new TYC radiator off Amazon - at ~$130, it is much cheaper than a Ron Davis, not fitment issues, and Arizona dry-heat-furnace tested by several of us :cheers:
Leave it alone. Or if you really just want to have a new radiator go the TYC as mentioned.
That may be what I end up doing...replace an "unknown" with a "known" to sleep better at night.
 
just make sure you use a tight-sealing cap for the TYC - OEM won't do it

@richardlillard1 had a post comparing the radiator caps somewhere here in the 80s forum
 
Back
Top Bottom