Superflex radius arms

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

With the announcement that the arms are being redesigned and shortened it would seem they figured that out.

Why do you always jump to a conclusion? With the expectation you know better. They where already done ages ago (not just announced). You keep saying they where designed badly, just because they dont work the dc shaft. Well, they arent suppossed too. Part time it. Or do what ever you want. All the other basses are covered. DC shafts are s***.

*Great flex
*Great road handling
*Caster correction
*Larger wheel clearance
 
Those are a solid inch further away than stock. So if the arms do correct for caster properly then the diff flange is pointing out in front of the t-case flange which would introduce some angle to the front u-joint that otherwise would not be there. That's why neither typical drive shaft will run clean on your truck. Too far out for a stock shaft but not close enough for a DC one.

With the announcement that the arms are being redesigned and shortened it would seem they figured that out.

This is a SF arm thread. SO not to clog it up. But I want to see photo's, pictures, anything to back this up. Because it simply isnt the case. All this points back to, is that your caster is not correct. Lets start another thread.
 
there are a ton of trucks with a 4" lift running around without vibrations. I never said that caster wasn't correct but the fact that if you install these arms you then have drive line vibrations that can not be resolved by the use of common drive shafts points to a design problem.

For someone who claims to be a suspension guru you seem to be blind to the obvious.
 
But this is the funny part about our arguments. You hang crap on things like these arms, saying its a "design fault". But I am still yet to see your shafts work with correct caster. I have no offiliation with superior in any way. Before you hang crap on something else. Show that your way works first.
 
That's hardly the "bolt-in solution" these arms are advertised as. I certainly wouldn't want to have to go with a part time conversion. I guess it's back to hoping somebody starts doing flipped arm conversions.

What are you looking for in a flipped arm conversion?
 
That's hardly the "bolt-in solution" these arms are advertised as. I certainly wouldn't want to have to go with a part time conversion. I guess it's back to hoping somebody starts doing flipped arm conversions.

A polished turd is still a turd. Its noones fault. If anyones fault its toyota's. After lifting your truck YOU WILL HAVE FRONT DRIVE LINE ISSUES.

That 20mm (if it is 20mm) is easily solved by running a 20mm spacer at the transfer output flange (custom spacer). Its the same angle/distance as stock. Then there is no difference to if the arms are 20mm longer or not. Its just a poor excuse at to why it didnt work with landtanks dc shaft. The reason it didnt work is because the arms correct caster for the required lift height. If you think correct caster is a problem. :D

Anyway, no more distroying this thread. Start a new 1, for flipped etc.
 
What are the US costs on these? I found one site with pricing in the $1,400 range, but didn't go far enough to see the shipping side of things.
 
But this is the funny part about our arguments. You hang crap on things like these arms, saying its a "design fault". But I am still yet to see your shafts work with correct caster. I have no offiliation with superior in any way. Before you hang crap on something else. Show that your way works first.

My way, what are you talking about? People have been using DC shafts with caster plates since they were introduced years ago. Where the hell have you been? It's not "MY WAY" it's just how it's done.

And why would the designer of these arms push the axle forward? In stock configuration the axle's center, horizontally speaking, is 2" above that of the rear frame mount bolt. After the 4" lift it is now 2" below the rear from mount bolt. So the axle is still in the same vertical plane as it was when stock just equally distance from the horizontal plane on the opposite side.

And to add to your love of caster. Using your number for degree change per inch of lift of 1.76, a 4" lift would change caster by 7.04 degrees. If you do a search you'll find that my caster plates rotate the axle by 7 degrees. I don't know what other plates do but I'm sure it's similar as the tolerance for a DC shaft to run clean is rather small.
 
For any newcomers to the party, concerning drive shaft spacers with the SE arms.

The drive shaft spacer will not correct issues with driveline vibes using an OE single cardan shaft on AWD 80.

A drive shaft spacer will not correct issues with driveline vibrations using an double cardan shaft on AWD 80.

The drive shaft spacer will engage more splined area at the slip yoke. That's it.
 
So no one answered the question: Are the new arms plug and play at mild lift heights from 2-3 inches, or do you need front driveshaft mods/new custom shaft? If you can just bolt them up to rigs with mild lifts for more front flex, then I would pay the $1500. But not if I'm going to have to get a custom front shaft, and or a part time kit.
 
To add one more component to they equation.

Without properly spec'd shock travel, or coils, there won't be an exponential improvement.

Have to have a coil that'll stay in the bucket, and a shock long enough to appreciate the articulation gains the arms may be possible of achieving.

Running L's, right now, the longest off the shelf I know of, and top out on the front long before the arms are capable of allowing.**


(**. Droop wise. I had to allow the front end to compress under it's own weight, to install shocks.

From an articulation perspective, it does better than other lifted 80s I've wheeled with, but I don't believe the difference is astronomical. Will know definitively once Radflo's are on.)

To answer you question, didn't know there was a "new" and "old" style arm, but you will get no guarantee from SE, either way).
 
There are longer shocks than L's that will fit at 2-3" of lift height. You may have to extend the bumpstops, but I won't be running L's. Spring retainers would keep the spring on the perches. So yes, I have no problem with maximizing spring and shock travel, I just want to know if the new design of these arms still requires front driveline mod/replacement at mild lift heights.
 
No guarantee... So this is not a bolt on design then, considering the complete change in front drive shaft. And then you still have vibes? No way I'm paying $1500 for that whole new set of issues, when I don't currently have any driveline issues! Just the same rigid front end most of us deal with. I'll just go the hitch pin route if this is true...
 
Dafun1 - Do you have a 2-3" lift now? Do you have any drivline vibs now? Fitting the arms does not cause anymore vibs. If you are really worried. You can make or buy a drive shaft spacer. AGAIN if you dont have any driveline vibs now (with the same size lift) then you wont after. Its jsut scare tactics and BS floating around.

And they give ALOT more travel. What Chris is saying, is that its the shock lengths that are letting down.

Stock.
C9733DBE-9627-4D3A-A0AC-E0D8ABF973A9-6438-0000069352FBF8E6.jpg


After
21BCCA0F-42F1-40FE-B6BD-D0B399439392-6438-000006935FAD244D.jpg


A3AC9871-6CE5-45D7-8906-85276223C715-6438-000006936533FDFC.jpg
 
Thanks BigBoy. And thanks for the contact Delancy. I'm still running stock shocks with a medium Ironman spring up front and the stock replacement height OME 862 in the rear. I've also unloaded about 1000lbs of GVW from chopping from behind the B-pillar and caging around the front two seats. Fenders are high clearanced as well. Heck, with as light as it is in the back, I might go back to some used stock rear springs! Running 38's now, but going up to 40's or 42's next tire purchase. These arms would be a simple way to get some flex and not completely bust the bank.
 
Back
Top Bottom