short bus vs. ARB

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Windshield Bar Anyone?

July 30, 2008

SCOTT CITY, Kan. (AP) - A Scott City man was killed in western Kansas when a deer careened off another car and smashed through his windshield.

Thirty-one-year-old Jason Kanak died Wednesday night after a deer hit by another vehicle flew into the windshield of his pickup truck on Highway 4 in Scott County.

The State Highway Patrol says the deer went completely through the truck and out the back window.

Kanak's wife, Lisa, was able to grab the steering wheel and get the truck back onto the road after it swerved into a ditch. Lisa Kanak and the couple's 4-year-old son were taken to a Scott County hospital for possible injuries.


Same highway I drove my eBay FJ62 w/ARB back from W. Pueblo in rut season '05. This area is the true FLAT Kansas, w/wheat fields running into the ditch (when there is a ditch). No trees, nothing to block visibility on either side of the highway. Muley? Whitetail? Could've been either. Evidently lacked the usual NRA gun rack &/or headache rack or the KHP would've said.

I've posted before on the INTIMIDATION FACTOR of the ARB. Jaywalking students return to KSU next week. Time to swap the LX back to the :princess: & drive around campus with my Sahara'd Tundra! :hillbilly:
 
Would a Ramsey RE series winch fit on the Short Bus? I'm also in between Slee and ARB, but if the RE's don't fit on the SB then it's ARB for me.
 
bumper decision

I had a bumper built by a local machinist.... I wanted something that suited the type of wheeling I due, and was good looking as well....

I suppose that question depends on what you are trying to accomplish and what is important to you...

1. Aesthetics?
2. Type of wheeling you do (functionality)?
3. Type of winch? Or no winch?

I'm not (personally) impressed by the ARB ad. The FJ80 has a tremendous frame. Any solid piece of steel attached to the frame will accomplish a similar result. I wouldn't sweat the protection issue too much (you're in a 6400# beast). I'd focus on what you want the bumper to accomplish in terms of performance, aesthetics, etc...

Darwin
 
I've had both and ultimately, it boils down to how you'll be using your rig.
The ARB is bigger and provides a larger superficial shield around your front end. It's also flimsier and will flex and damage your body when you're climbing rocks, etc. If you don't "think" you'll ever be climbing big rocks, the ARB is probably the best overall choice.
The Shortbus is lower profile from all angles but is much more stout. The Shortbus was not available when I bought my ARB, but even if it was I may not have chosen it. It took actual wheeling to point the shorcomings of the ARB. In the end, the Shortbus is a dramatically better bumper for what I need it for.
 
I just notice where my ARB has been coming up into my body. I would order a short bus today and put my ARB up on Mudbay if I could get the short bus with the upper bars of the ARB.
 
I just notice where my ARB has been coming up into my body. I would order a short bus today and put my ARB up on Mudbay if I could get the short bus with the upper bars of the ARB.

That was the only reason I went with the ARB, I like the Slee bumper, but I feel like I need the added protection. If Slee would offer it with that type bar and keep the price reasonable I believe he would probably double sales.
 
I want a short bus but would settle for a really cheap used arb since i am on a budget. When you upgrade let me know. The savings can go into the welder fund so that I plate the back side of the arb.
 
X2

We hit a deer at 70 in my wifes 80 with the ARB on and no damage whatsoever. Now with the Short Bus, that deer would have been in the front end and cause damage.

I would choose for what your main uses would be...if no deer or roo's in your area, then Slee. Or just add to the Slee.

arb on my '93 :cheers:
 
I have an ARB on my 80. Ive have an ARB on just about every land cruiser ive owned. 40, 60, now 80. I do like the slee bumper, but i already had a m12000 sitting in the garage from my 60. I didnt think it would fit the slee bumper and i didnt have the funds to buy another winch when i had a perfectly good one already. But, if it, the m12000, does fit, i would think about getting a slee bumper.

jon.
 
But, if it, the m12000, does fit, i would think about getting a slee bumper.

jon.

It was established in another thread that the M12000 does fit the slee bumper.
 
It was established in another thread that the M12000 does fit the slee bumper.

A 12k WARN winch will NOT fit. There are other 12k winches that are smaller that does.

Yep, my bad- search up in this thread and it was a mile marker winch that was installed.....
 
Off road - Slee if you like the looks.

On and Off Road - ARB hands down.

For me ARB either way. Now if the Slee had the added protection of the ARB????

I've run into, over and through some pretty serious stuff with ARB's over the years and have yet to incur any body damage. Animals, trees, cars, etc.
 
I just installed the short bus on my truck over the weekend. Since I have a Mile Marker 12k hydraulic winch there was some concern of fitting that in there. Well after some clocking and re-routing of the hoses it looks like it was made for it.

Landtank, I found your hydraulic Mile Marker install into your old ARB, but can't find anything about the hydraulic install into your new Slee Shortbus. I have two questions:

(1) Are there some pictures or a dedicated thread that about your install? I'm specifically interested in how the winch needs to be clocked in order to fit (in this thread you write: "I used spacers....[and] clocked the drum so the lever faced up instead of back.")

(2) From this thread, I gathered that I would need a Mile Marker hydraulic winch with an "integrated control valve" in order to fit it into a Slee Shortbus bumper. This would mean that I'd need one of the "HI" series winches (I would be looking at running a 10.5K or 12K lb winch). Is that correct ?

Thanks, Landtank.

P.S. - I ran some of the trails in Troy, NH that YT did last week and ended up winning a winch at the event(!). Now, I'm trying to figure out which winch and bumper combo to go with (the ol' Slee vs. ARB debate). If I'm ever going to attempt the trails, like "Wombus Pass", that Nat (and maybe you) were running, I'd feel better having a winch.
 
I don't know how easy it would be to get one since there are no authorized dealors in the U.S. (assuming you're in the U.S.), but Ironman 4x4 also makes a bumper for the 80. I think it's a good looking bumper, I've seen them on some of the Venezuelan 80's that run the Funrace 4x4. I don't know that much about it, I plan on inspecting it better the next time I'm down in Venezuela, but it holds up through the Funrace 4x4, so it must be pretty tough as those guys are pretty hardcore. http://www.ironman4x4.com/
 
the original thread dealt with installing the Hydraulic winch on the ARB. The install on the Short bus is much the same except you are feet down on the short bus and feet forward on the ARB.

Clocking the gear box basically means rotating it so the controls are facing a direction that can be reached.

I liked the install on the short bus better than the ARB. Since the winch has an integrated valve assemblty that has to be taken into account when mounting the winch.

On the ARB that valve had to stand vertically and up above the top of the bumper.

On the Short bus it was horizontal and very well protected.

outside of fitting the winch to the bumper the rest of the install was the same. So the hose length and routing in the first thread applies to both installs.
 
Thanks for taking the time to reply, Landtank.

Since you didn't disagree that the "HI" series of Mile Marker winch is the one to buy, I'll assume that you have the "HI12000" winch installed in your Slee bumper and I'll be aiming in that direction.

:cheers:
 
Correct me if I'm wrong with this info (gathered from other threads)

Bumper Weight

Short Bus - 90lbs
Non Winch ARB - 130lbs
Winch ARB - 150lbs

From a daily driver concern weight would be a big factor in my potential selection of a new bumper. More weight adds to the crappyness of 80 mileage, increases front sag, and increases yaw moment. Based off this info I would go with the lightest bumper for my rig. A plus to the ARB if you live in a deer heavy area (Deer strikes always suck). Maybe Slee offroad should consider making a "poser edition" short bus bumper out or 1/8" for us tools that just want the look of a H/C bumper. Just sayin.......
 
Maybe Slee offroad should consider making a "poser edition" short bus bumper out or 1/8" for us tools that just want the look of a H/C bumper. Just sayin.......

Maybe you should look into a tube bumper.
 
Back
Top Bottom