OME spring install question. What helps

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 29, 2005
Threads
156
Messages
848
Location
Golden Colorado
Im doing the 861 and 862 OME spring only. Seems my LX 450 has a serious case of the sags. I have done quite a few searches and looked around for threads on installs. I found Christos how to thread and that will help but what other tips or tricks do you have on the spring install. I have heard people say they can do all four in an hour or two and others say 4 or 5 hours. What are those that can crank them out that quick doing or skipping to help.

I have two floor jacks, 2 bottle jacks, and a set of jack stands as well as a high lift. When I ordered them from Christo they mentioned the high lift but I didnt see this in the how to article??? ( would I use the high lift to just jack the ends up, udo the mounts and let the floor jack lower the axle???)

Thanks for any help at all. I have never really worked on suspension (other than motorcycle) this is all new to me. I will be doing the install Thursday or Friday this week
 
You need to drop the entire front axle on both sides since it doesn't flex well. Once you have disconnected the shocks it should droop plenty. The rears can be done one side at a time.

You don't need to be gentle. I use a 4' breaker bar and/or crowbar if a spring needs a bit of extra encouragement to get over the lip of a spring pad. This will save you those hours of aggravation that people mention. If it is on the pad, but just won't clear the lip, put on a set of heavy soled boots, stay clear of the vehicle underside, and kick the thing over the lip. You may be amazed at how effective that little trick is for a spring that seems like it just won't move.

I do recommend you work with a friend if you have never done this kind of work before. Putting a vehicle on jackstands and working on the supsension can be dangerous, and it can be a tough one person job if you aren't comfortable with all of the tricks. Two people on this job far more than doubles your capability, including rational decision making if you get stuck. Make sure the jackstands are level and in full contact with the frame rails at all times, and lower the axle slowly with your floor jack.

And finally, make sure you have the right socket sizes and other tools - nothing extends a suspension swap like trips to the hardware store. :cheers:
 
Where you at in Colo? I could lend a hand if needed. A trick I use if having trouble is to put a bottle jack on top of the axle and jack against the frame if you cant get the droop you need. Undo the shocks and the sway bars and I wouldnt think you should have a problem with the 3" OME. PM me
 
As long as you get the lower shock mount disconnected and the sway bars as well, you'll be fine.

If you have rust issues I strongly recommend soaking these points with PB blaster or it's equivilant a few days in advance.

The only thing you need to worry about is getting TOO eager and letting the axle droop too far once it's disconnected from the shocks, thus stretching the brake lines.
 
You need to drop the entire front axle on both sides since it doesn't flex well. Once you have disconnected the shocks it should droop plenty. The rears can be done one side at a time.

You don't need to be gentle. I use a 4' breaker bar and/or crowbar if a spring needs a bit of extra encouragement to get over the lip of a spring pad. This will save you those hours of aggravation that people mention. If it is on the pad, but just won't clear the lip, put on a set of heavy soled boots, stay clear of the vehicle underside, and kick the thing over the lip. You may be amazed at how effective that little trick is for a spring that seems like it just won't move.

:

I'll disagree with Nay here - you should be gentle and pay attention to how much you're stretching the brake line. With the bracket removed you won't really have an issue but just be aware of it before you get too carried away. No reason to need a breaker bar, they'll go in just fine if you follow Slee's instructions. If you need to push the axle down a little to create enough space to get the spring in just put a bottle jack between the axle and frame and then use it to push the two apart in a nice controlled manner - again, a tip from Slee's instructions. Additionally, be gentle with the lower shock mount bolts and soak them with PB blaster in advance. Mine came out easily but others have snapped them off. Be sure to coat the lower shock mount bolts with anti-sieze before putting them back in - this will save you from sweating them in the future. Once you get in there you'll get a great idea of how the suspension works and the instructions will make sense.

There's no need to get a hi-lift. That is only mentioned as an alternative method. Jack stands, bottle jack, floor jack is all you really need.

It's really not that hard if you take your time and focus on safety. Don't worry about being able to do it in X hours etc. Just start in the morning and even with taking breaks you'll easily have it done before dinner. Those who are quick at it have done it a few times. Your second time around when you're installing a taller lift :D will go much faster. As said by Nay, a buddy will make the job easier and safer.


EDIT: Just noticed you were in Colorado ---- there are plenty of good folks in your area that would likely be happy to lend you a hand.
 
Last edited:
You can do the front one side at a time. Watch the brake and ABS lines. You'll probably pop the axle breather off, just put it back when you're done. As others have said, undo the shock and sway bar. I had someone step on the hub and press down to get enough space to slip the springs in and out. You can also rent spring compressors from most auto parts places, they're handy but not required.
 
I think it took me about 3 hours to do the J spring install on mine a month or so ago. I did the front one side at a time. I borrowed some spring compressors from a fellow club member. They were helpful for sure.

if you've got air tools and spring compressors, I think it could easily be done in a couple hours. I was only using hand tools which slowed it down with the spring compressors, but still wasn't bad.
 
Yeah, I read all the posts about installing various lifts in 1-5 hours. My experience was different. OME 3.5" with the 4Plus drop brackets. 2 days. Average/slightly above average garage abilities. Above average tools. Read everything that I could find prior to starting (Slee's write up is great)

Expect the worst and hope for the best. I found a lot of corrosion, stripped bolts, seized bolts, and a steering stabilizer that loved the truck so much it didn't want to leave. That steering stabilizer sucked down more time than some have published taking for the entire job (4-5 hrs). Pickle forks, Pitman pullers, air chisels - it really did not want to come off.

Anyway, its not a race. It was great to have the chance to spend a couple days messing with the truck - learning. I say that now - there was a lot of swearing during the process. I just wish I had planned for that much time. I thought it was a 3 hour affair going in to it. Ha. Enjoy the process.
 
I'll disagree with Nay here - you should be gentle and pay attention to how much you're stretching the brake line.

I only meant this in terms of the coils. Pay attention to brakelines and everything else. What I meant is once you have the axle drooped to its max, if you have a coil that just won't pop over the lip of a spring pad, you don't need to be gentle, or use coil compressors (they scare the sh$t out of me). A breaker bar can give you the leverage to get a bit of coil compression to pop the springs into place if you need it, and a nice big kick can work better than anything.

You shouldn't need this for stock height springs, but the first time I ever did an OME install it took me 3 days and the rig was new and had no rusted bolts, and I can swap basic height springs and shocks by myself in about 90 minutes now taking my time and working through any typical obstacles.

One final note: a hand winch (come-a-long) is one of the best and most versatile lift installation tools you can buy. The applications are just about endless when it comes to axle location and bolt removal (you shouldn't be dealing with any of this, though). I was lazy in installing my FOR 3" coils, which are pretty long to avoid coil unseating, in not wanting to unbolt any extra stuff and with two people used a combination hand winch and floor jack (plus a good solid boot) to get the last coil seated. Very interesting and unrecommended approach, but perfectly save and effective :grinpimp:
 
One final note: a hand winch (come-a-long) is one of the best and most versatile lift installation tools you can buy. The applications are just about endless when it comes to axle location and bolt removal

I have no idea how you'd use a come-a-long for bolt removal, and unless you're dinking with the control arms (which you won't be), the axle shouldn't move anywhere laterally.
 
I have no idea how you'd use a come-a-long for bolt removal, and unless you're dinking with the control arms (which you won't be), the axle shouldn't move anywhere laterally.

You wouldn't for a basic OME install, which I qualified in my post. Point was as you get into this stuff it is a great tool for installs, especially those done alone. From stuff as simple as changing out panhards and needing to recenter the axle to control arm swaps to the more complicated. Basically, any time you have load on an axle of any type and need to remove a bolt or shift the position of the axle, a come-a-long may well be the best friend you ever had.
 
if you have disconnected the shocks and sway bars and dropped the axle down as far as it goes and find that you need to bar against the axle to get the spring in, I'd put something under the axle to support it so as not to damage the ABS harness or brake lines.


I set my jack stands at the highest position and on the truck frame
and used my floor jack under the diff to control the droop.

As someone already said, use PB Blaster on all bolts you will need
to loosen a few days in advance.
 
I set my jack stands at the highest position and on the truck frame
and used my floor jack under the diff to control the droop.

As someone already said, use PB Blaster on all bolts you will need
to loosen a few days in advance.

Where exactly did you position the jack stands on the frame when doing the fronts and when doing the rears? I'm about ready to do mine too. A pic would help if possible.
 
I put the jack stands just after the control arm mounts on the front of the frame and just before the control arm mounts on the rear of the frame.
 
Where exactly did you position the jack stands on the frame when doing the fronts and when doing the rears? I'm about ready to do mine too. A pic would help if possible.

As close to the lower control arm mounts as possible while still maintaining a good "seat" of jackstand to frame rail. So just behind the front mounts for the front springs, and just behind the rear mounts for the rears springs.

In terms of visualiing this, you want as little of a "see-saw" support as possible without compromising stability.
 
I plan on putting my 6" springs in tomorrow after dinner :)

Just be careful and read up on the above recommendations. It is pretty straight forward, just be aware of your brake lines, etc and do one side at a time.
 
Sorry to hijack, Dan did you go with Slee's or OME's 6" springs?
 
Slee. I needed the heavies for the rear. OME Comps aren't true 6" and they aren't rated for what I need. That, and the Js and spacers I have one are WAAAAAAY to soft for my big heavy boat :)

/hijack
 
Where exactly did you position the jack stands on the frame when doing the fronts and when doing the rears? I'm about ready to do mine too. A pic would help if possible.

I put the jack stands just after the control arm mounts on the front of the frame and just before the control arm mounts on the rear of the frame.


I didn't take any pics, but that sounds right.
 
Back
Top Bottom