Issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2004
Threads
234
Messages
4,449
Location
Bozeman, MT
Ok so I am having some issues right now and I'm not sure what the problem is, just want to hear some opinions as to the problem. I got the cruiser fired back up the other day and when I would rev it high it was backfiring out of the carb. Adjusted all the valve clearances a couple times and seems the problem was fixed but it was still running rough. So I went a borrow a 1 barrel from a guy who cleaned it and reassembled and put it on. Smoothed it out a good bit and still no backfiring. So I took it out for a spin once I get high in first gear it starts dying on me and if I rev real high it seems to start to die out some. Also once I got into second gear as I started up any kind of hill it would start dying too. So I can back adjusted the dizzy and fuel mixture and took it back out to the same problem. So let me know what you think so I can run through it on thursday when I don't have class. Thanks.
 
Not sure about vaccuum leaks kinda sounds like one but I can't find one anywhere. Timing is a possibility I'm gonna borrow a timing light tomorrow hopefully. I just installed a new electric fuel pump and it was pumping good. Fuel filter is the clear kind in the line and it looks fine. Plus its a brand new fuel cell with brand new lines so there shouldnt be anything in it.
 
Clogged fuel filter is very likely, fuel pump, and entire fuel delivery system is likely. You didn't specify how it looses power. If you are in the throttle but steady and it seems to run out of fuel then look at everything from the tank to the float level. The accelerator pump only is active when you add throttle, it squirts a shot to richen the mixture between jets.

Timing won't cause it to loose power that was there after a while at steady speeds. Nor will a vacuum leak. The fuel mixture only effects idle and until the trottle plates open.

So unless I missed when/how it's dropping off, I'd scrap the electric fuel pump and replace the filter and before I connected the lines back up to my carb, I'd turn it over and watch the flow from the pump for crap.

You didn't mention if you installed a regulator, but if you did, crank it up.
 
bandy rooster said:
stuck float bowl?


X2. It's REALLY easy to bend the float arm sideways on the 1bbl carbs when you're removing & installing the upper air horn. It gets wedged against the wall of the bowl and won't move. When I bent mine, it would still run, but it never filled the bowl and would die if ran above idle.

Get a buddy to watch the sight glass while you rev it up in the driveway. You might not be able to make it die, but you also shouldn't be able to even notice the level changing. Of course, this could also point to fuel pump as SG pointed out, so you've got a few things to check out.
 
Its pumping a steady stream of fuel I didn't put a regulator on it. As for when/how it dies it is fine up through first gear until I get to where I need to shift when I shift up to second and try to accelerate is when it starts to die out. Basically when I am on the accel pedal with anything other then steady light pressure. I'll check the float. I can't look through the glass though it had a crack in it and the guy I got it from put some sort of epoxy or something over it to keep it from leaking so I can't see in it. I checked the filter again and its clean and the lines are brand new only had fuel in them 3 times and the fuel cell just got gas in it for the first time like 2 days ago so there is definitely nothing clogging the lines or anything like that.
 
clogged fuel line, i had a prob when i went get on the gas it would hesitate then start going, got pissed rip the truck apart and switch the fuel hardline, then i squirted some cleaner through the old line and i was amazed at the crap and sludge that came out.
 
Let me reiterate, it is not the fuel lines they are not clogged they are brand new have only had fuel run through them about 3 times total both times out of new fuel cells. Sorry to getting edgy but I know this is not the problem and I want to figure out what is and I'm getting aggravated with it.

I adjusted the points and readjusted the dizzy this morning and it is better then it was. Running a little smoother but it still starts to die out in second. If it is just sitting in the driveway and I rev it then the cruiser will rev high without dying out. But when its driving and I rev it high it starts dying. Just an update to see if it will help any.
 
If you pull the upper air horn off the carb (don't even need to take it off the intake), you should be able to visually check to see if the float is hitting the wall of the bowl. Also, it could just be out of adjustment with regards to the needle valve. There is an adjustment procedure in the FSM that gives very specific gaps - sorry I don't have it in front of me.
 
Marshal I'd be up for some help tomorrow man. Depends what time and stuff though.

As for the float I removed the top of the carb and checked i and it doesnt seem to be hitting in any way.
 
What your explaining is classic insufficient fuel delivery symptoms, it takes a bunch more fuel to run the motor under load than revving it in the driveway. A couple of things to check, is there any air in the filter? If so you may have a leak between the intake (suction) side of the pump and the fuel pickup, the fuel is under vacuum and will not leak out, but will pull in air. Fuel pumps don't like pumping air, they will free flow a bunch of fuel but won't deliver much fuel under pressure. To test pull a rubber line close to the carb, T in a fuel pressure gauge and add some output hose to a container to catch the fuel, run the pump and pinch the output hose after the gauge, if you have good output at 3-5 psi your golden.

The next place to look is the carb, there are two places that can cause this. The first is the fuel inlet/needle and seat, with the float hanging (float bowl empty or top off the carb) blow in the inlet, you should be able to easily blow through. If not remove the fuel inlet, float and needle and seat, most times there is a small filter in the fuel inlet fitting or it only takes a tiny bit of debris to restrict the opening in the seat.

The next place to look is the main circuit, from the main jet in the bowl to the venturi in the throat, take a can of carb cleaner with the extension hose on it, push it against the main jet and blast. The cleaner should spray out in the carb throat, if it's restricted remove the main and air jets and clean out the jets and passage.
 
clemson55 said:
Marshal I'd be up for some help tomorrow man. Depends what time and stuff though.

As for the float I removed the top of the carb and checked i and it doesnt seem to be hitting in any way.


Just call and let me know.
 
I had the same type of problem when I installed a new polly tank and lines on the 40 - sometimes the tanks have debris in them and clog up the filter. I was sure this wasn't the case as well being all brand new and a new filter ... but put on another filter and the issue went away. Mine was only at high RPMs as well -

Good luck!

Tucker
 
Back
Top Bottom