Having Robbie for 10 hours

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 8, 2015
Threads
61
Messages
778
Location
Somewhere
Imagine that you would have Robbie for 10 hours before long trip (15k miles). What would you like him to check / do. The budget is 10 hours / 1000 dollars.

I think about following list:
  1. preload wheel bearings. I am not sure if I did it right when done the front axle. And I will be doing rear axle soon. (2 hours)
  2. Install new engine mounts. This looks like pain in the ass to me. (2 hours)
  3. Change u-joints (2 hours)
  4. Install rear aussie locker (3 hours)
  5. Have a beer (1 hour)

The car is in very good condition, I don't think that engine needs some care as I did head gasket recently. I am really looking only at drivetrain. I also asked him what would be the charge for changing all bushings (front, rear everything) which he says would be 8 hours.

Jorge
 
the first 3 seem pretty mundane to me. Seems like you'd want to have him do stuff that the average tech or DIY can't do.
 
PHH....All by touch.
Engine Bay Fuel Filter!
Adjust the valves, but have the valve cover already removed?
Ensure the timing is correct?
Clean the MAF (95-97)

I could show him how to snap the plastic nipple off a radiator in no more than 5 seconds :eek:
 
PHH....All by touch.
Engine Bay Fuel Filter!
Adjust the valves, but have the valve cover already removed?
Ensure the timing is correct?
Clean the MAF (95-97)

I could show him how to snap the plastic nipple off a radiator in no more than 5 seconds :eek:
All this was done by me when doing the head gasket. From the engine there is nothing else to worry other then mounts right now.
 
All this was done by me when doing the head gasket. From the engine there is nothing else to worry other then mounts right now.

Arch Oil Pan Seal was replaced? I think it involves the Engine Mount Bracket.
 
Imagine that you would have Robbie for 10 hours before long trip (15k miles). What would you like him to check / do. The budget is 10 hours / 1000 dollars.

I think about following list:
  1. preload wheel bearings. I am not sure if I did it right when done the front axle. And I will be doing rear axle soon. (2 hours)
  2. Install new engine mounts. This looks like pain in the ass to me. (2 hours)
  3. Change u-joints (2 hours)
  4. Install rear aussie locker (3 hours)
  5. Have a beer (1 hour)

The car is in very good condition, I don't think that engine needs some care as I did head gasket recently. I am really looking only at drivetrain. I also asked him what would be the charge for changing all bushings (front, rear everything) which he says would be 8 hours.

Jorge
I will not excuse me, I am on both time stress and I simply don't have the equipment to do this stuff. I agree that u-joints shall be done by me. Regarding preload it is more of experience then willingness to do that.
 
Arch Oil Pan Seal was replaced? I think it involves the Engine Mount Bracket.
Nope this was not done. The rear is leaking a little bit almost not noticable. The arch oil pan is constructive and thanks for this. Do you think that the access should be easier when doing the engine mounts ?
 
Imagine that you would have Robbie for 10 hours before long trip (15k miles). What would you like him to check / do. The budget is 10 hours / 1000 dollars.

I think about following list:
  1. preload wheel bearings. I am not sure if I did it right when done the front axle. And I will be doing rear axle soon. (2 hours)
  2. Install new engine mounts. This looks like pain in the ass to me. (2 hours)
  3. Change u-joints (2 hours)
  4. Install rear aussie locker (3 hours)
  5. Have a beer (1 hour)

The car is in very good condition, I don't think that engine needs some care as I did head gasket recently. I am really looking only at drivetrain. I also asked him what would be the charge for changing all bushings (front, rear everything) which he says would be 8 hours.

Jorge


If you can afford to 'hire' Robbie, I would go for it. He is amazing and amazing to work with. My only caution to you is that your 'while I'm in there' list might grow substantially !! He can and will do anything you ask and is truly competent.
 
@Jorgito save your money on the pre load adjustment. Bring it to me if you want and I will adjust them. It would probably take about 30 min start to finish for both sides. Its super easy after you've done it a few times.

Have him check your belt tension, radiator hoses, alternator output, stuff that's easy to overlook but will leave you stranded.
 
I'll just say he works a hellofalot faster than me...:eek: but it would be nice to have a real pro do some things right!
 
Robbie is probably one of the best 80 mechanics in the US. He is well know as probably the best rebuilder of 1FZ-FE's anywhere and at one time from the numbers Cdan and Beno had, he definitely did more rebuilds than anyone else.

I don't know who Robbie is, but if he can find my wiring problem, I'd pay him $1000, regardless of how long it takes.
 
I would have Robbie inspect the rig and take his evaluation on how your $$$$ would be best spent?:idea:
 
Ditto, said better than me !!!
I already did that when I bought the car. I followed all what Robbie told me. I am just more into what you guys should do before such long trip. Most probably I will just leave it to Robbie to whatever he thinks is good to do in 10 hours.

Jorge
 
... Most probably I will just leave it to Robbie to whatever he thinks is good to do in 10 hours...

I think you've got it now.
 
You just did the most dreaded maintenance item we do, the HG. I see no reason why you can't do all these other things on your list by following the FSM and asking questions like you did during the HG job.
 
Id have Robbie doing lots of push-ups - and alot of cardio......cut down on the fatty foods and eating some more greens! - we gotta keep this guy healthy so he can fix our s*** well into his grey-haired years !!!! :) or is he already grey?
 
Last edited:
Back
Top Bottom