Fun with birf/knuckle service

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 9, 2007
Threads
39
Messages
118
Location
Kennedrunksnort Maine
So this didn't go as planned and ran into roadblocks..I was able to get the birf assembly and everything out smoothly..grease was good and no gear oil but have had clicking and crunking in the right side for a while...when moving onto trying to free the knuckle, struggled to remove tie rods from lower arms without a puller but when my neighbor arrived, finally freed it only to be foiled by snapping one of the four bottom arm bolts. On to snapping off 5 of 6 10mm bolts(hand tools-no impact) in the rear knuckle wiper/gasket area. After that frustration and temps. in the teens with 20mph winds in a partially closed garage, I had to admit defeat. Have the confidence and parts to do it but now with having to drill out bolts, not really something I wanted to face.

Advice on drilling out the 10mm stripped/snapped bolts? Not too concerned about drilling out the lower arm bolt.
 
I'd just break/rip the wiper seal plates off. Bend until they break. Most kits come with new parts anyway, so no loss. Pull trunnions out to separate the knuckle housing from the axle. Once things are cleaned and on the bench, you'll have much better conditions to evaluate options. Perhaps there'll be enough stud left to get some vise grips on it. It not, cut-drill-tap.
 
I've had good luck with the left handed (reverse cut) drill bits in the past... Easy out might work with them being that small. I'd first spray the crap out of the area with PB blaster and let that soak for a while before trying anything.
 
I broke one of those, too. I got mine out with a L handed bit and EZ out from Amazon. I wouldn't drill and tap if it were me. I'd be afraid to screw up the angle, and the angles are important with these parts. If the above suggestions didn't work, and it were my truck, I'd buy a used knuckle. Of course, if it's your DD and it's down, that might change the analysis a bit. Sometimes you just have to get it back on the road. Good luck.
 
If you don't weld / have one - PB blaster & time. If you want to speed it up, get a good blowtorch head & a bottle of MAPP gas --the yellow cylinders @ Lowe's / Home Depot. With a good head & the real gas, you're close to acetylene for temps, something like 2K* C + . An oxy/ace torch does ~2800*C (from memory).

At any rate, a $40 torch, and a bottle is ~$15 - you can't beat the portability & uses for a good blowtorch. That torch is intended tool for sweating copper water lines in your house, unless you're new enough to have PEX pipe. Plus a propane bottle is $3, so you have a great BBQ / campfire starter.

I use mine plenty, only resort to the oxy torch if I'm blowing out bolts.
 
If you have a welder, weld a washer to the broken bolt, then weld a nut to the washer. The heat from the welding will more than likely be enough to break everything loose.
This is really the easiest/best way 95% of the time. Even if you have to bring the knuckle to someone this will probably be easiest.

Wait, I'm just north of you in Portland. Bring it up and I'll get them out for you, no charge.
 
If you want to speed it up, get a good blowtorch head & a bottle of MAPP gas --the yellow cylinders @ Lowe's / Home Depot.

Just make sure you clean the grease from the knuckle first. Grease and 2800*F is a nasty combo. A little, no problem. More then a little - I lope you have a fire extinguisher nearby.
 
Just make sure you clean the grease from the knuckle first. Grease and 2800*F is a nasty combo. A little, no problem. More then a little - I lope you have a fire extinguisher nearby.

Ahhhhh, what fun is safety :p - send the kids out to play "lawndart chicken", or hand them some fireworks to entertain themselves while you do this :skull: o_O :skull:.

Srsly, good point - while a small tool (rimshot) , it packs a punch esp for $$$ spent.

A Victor rig without bottles or extras like tips & cleaners, or a longer hose - is a good chunk of change & figure $400 for bottles you buy filled. Say about $600 to get going in a oxy ax (guessing, mine's old).
 
Ahhhhh, what fun is safety :p - send the kids out to play "lawndart chicken", or hand them some fireworks to entertain themselves while you do this :skull: o_O :skull:.
Straying off topic, as so often happens ...but some people should not have fireworks.
 
So this didn't go as planned and ran into roadblocks..I was able to get the birf assembly and everything out smoothly..grease was good and no gear oil but have had clicking and crunking in the right side for a while...when moving onto trying to free the knuckle, struggled to remove tie rods from lower arms without a puller but when my neighbor arrived, finally freed it only to be foiled by snapping one of the four bottom arm bolts. On to snapping off 5 of 6 10mm bolts(hand tools-no impact) in the rear knuckle wiper/gasket area. After that frustration and temps. in the teens with 20mph winds in a partially closed garage, I had to admit defeat. Have the confidence and parts to do it but now with having to drill out bolts, not really something I wanted to face.

Advice on drilling out the 10mm stripped/snapped bolts? Not too concerned about drilling out the lower arm bolt.

For the 10mm Bolts, If there is any thread protruding use a Vice Grip after heating them and hitting with a shot of PB Blaster. Next I cut a slit with a dremel then used a Lg Screwdriver and a Vice Grip on the screwdriver.
 
Sent
This is really the easiest/best way 95% of the time. Even if you have to bring the knuckle to someone this will probably be easiest.

Wait, I'm just north of you in Portland. Bring it up and I'll get them out for you, no charge.
you a PM Notch-thank you
 
Thank you for the all the replies and advice. Hopeful I wouldn't need to find a used knuckle. I wasn't really torqueing hard. Using barely any force and these felt like they dissolved under pressure. I had sprayed PB and penetrating on these before starting.
As far as removing the tie rod, it looked easier to have that room to move the knuckle for rear access in order to fully clean, disassemble, new wipers/seals/gaskets/etc. etc. Right parts from Kurt and Cruiser Outfitters and wanted to do it right. Poor choice of weather days.
 
And then I find out my driveshaft is toast. Barely hanging on. Not the best lead up to Christmas. OEM on driveshaft or something else? Not going bigger than what she rides on at 285/75/15. Already on OME lift.
 
And then I find out my driveshaft is toast. Barely hanging on. Not the best lead up to Christmas. OEM on driveshaft or something else? Not going bigger than what she rides on at 285/75/15. Already on OME lift.

Junkyard shaft. Check on ebay for front shafts. Dime a dozen.
 
looks like youre in good hands already with getting them out..

you definitely have to get creative living in new England with breaking rusty bolts free..Im from cape cod originally.
I used to do multiple heat cycles with a torch and pb blaster. Get it red hot, wait another few minutes with the torch still on it, then hit with PB. then repeat the heat..
I would do this around 5x's and tapping the bolt/housing with a hammer periodically to break things free. Ive never tried the welding trick though. that'd probably work just as nice.

Oh, and melting a crayon into the threads helps tremendously too.
 
Back
Top Bottom