Disk brake conversion Master Cylinder Challenges

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

bsevans said:
A MC from a 92-94 LandCruiser will bolt right in and already has the proportioning for four wheel disk brakes. No fuss, no muss.

okay BUT he does not have 4 wheel disks and he bought a 78 MC he wants to make work. :confused: he would still be in the same boat with needing to remove a vavle as he has rear drum.

anyway, what is the update Fast Eddy??
 
bsevans said:
A MC from a 92-94 LandCruiser will bolt right in and already has the proportioning for four wheel disk brakes. No fuss, no muss.

Sorry for the hijack, but can you provide more info on this as I am getting ready to put put for wheel disc on my 71 via Poser's rear bracket and a 76 front end.

I now return you to the regular thread. :doh:
 
Continuing problems.

To all those on some FAQ thread I read that said you don't have to bench bleed your MC: bzzzzt

To anyone getting a new MC: bench bleed it

I didn't do it, hoping that I wouldn't have to, and having done it in the past without bench bleeding first, and I was up until 11 and went to bed disappointed. We'll take it apart again today and try again.

I didn't open it up to look for residual pressure valves. I'm hoping it's right.

My original (I think) booster rod adjusted all the way in was pushing a bit on the MC plunger. I trimmed off about 5mm with a dremel tool. I don't know why, but I don't see what it could hurt either.

I also got my 2nd wrong-part-in-the-right-box from Toyota in 2 weeks.

I was so busy and frustrated I forgot to drink beer. :crybaby:
 
Fast Eddy said:
To all those on some FAQ thread I read that said you don't have to bench bleed your MC: bzzzzt

To anyone getting a new MC: bench bleed it

I didn't do it, hoping that I wouldn't have to, and having done it in the past without bench bleeding first, and I was up until 11 and went to bed disappointed. We'll take it apart again today and try again.

I do believe in the bench bleed 100% - but not that it has to be done in an actual 'bench' off the rig. As my link shows, I had awesome results doing a bench bleed on the rig (and so have several other well known guys on this board). That being said, bench bleeding was one of the faster steps in the process. pretty easy to do I found.

Fast Eddy said:
I didn't open it up to look for residual pressure valves. I'm hoping it's right.

"hoping it's right".. dude, why not just open it up and find out - if not, you could get screwed and do it all again when the circut does not function properly? just unscrew the copper nut where the b nut screws into and see if it is there? do it on the rig prior to bench bleed. takes less than 5 minutes to do this.
 
Last edited:
wantatlc said:
okay BUT he does not have 4 wheel disks and he bought a 78 MC he wants to make work. :confused: he would still be in the same boat with needing to remove a vavle as he has rear drum.

anyway, what is the update Fast Eddy??
Checking his first post, he does have 4wdisks. On the 78 master the front cup is for the front disk axle. The rear cup was for drum. Underneath the large nut for the brake lines is a residual valve. Both front and rear have a valve. The front is a 2lb line pressure, the rear 6 lb. The rear has a higher pressure to hold the drum shoes closer to the drum as the shoes are pulled back from the drum with a spring. Remove the rear residual valve and replace with a 2lb valve and use a stock 78 proportion valve and you will have no problem. If you cannot locate a 2 lb valve and a stock proportion. Remove the 6 lb residual and install a wildwood adjustable proportion valve in the rear line. Installing a later 4 wheel disk brake master solves the master problem but will still need to install a proportion vavle of some type.
 
Plowboy said:
Checking his first post, he does have 4wdisks.

not - the first post is by FJ40LVR who does have 4 wheel disks BUT bsevans quoted a post by Fast Eddy who does NOT have 4 wheel disks - and my quote was to that effect.
 
wantatlc said:
I do believe in the bench bleed 100% - but not that it has to be done in an actual 'bench' off the rig. As my link shows, I had awesome results doing a bench bleed on the rig (and so have several other well known guys on this board).

This may be a semantic distinction, but if you are bleeding the master after installing it in the vehicle, you are not "bench bleeding" it.

Bench bleeding is when you chuck the master in a bench vise, install the little recycling tubes to pump the fluid back into the reservoir, fill it with fluid and pump it until there are no more bubbles. Then you install it.

What we routinely did at the shop was to install the master, install the brake lines finger and crack them open a half turn, fill it, pump it a few times (tightening the nut before you let up the pedal) to prime the master (catching the fluid in a shop rag) tighten the fittings and then bleed the cylinders/calipers.

It maybe only saved 5-10 minutes, but this adds up in a big shop that does 5-10 brake jobs a day. You need to do it efficiently and with no bring backs. If it didn't work or it caused returns we wouldn't have done it that way.

Bench bleeding will never hurt, but my point is that it isn't necessary and you can bleed it on the truck without recycling the fluid back into the reservoir.
 
Pin_Head said:
This may be a semantic distinction, but if you are bleeding the master after installing it in the vehicle, you are not "bench bleeding" it.

Bench bleeding is when you chuck the master in a bench vise, install the little recycling tubes to pump the fluid back into the reservoir, fill it with fluid and pump it until there are no more bubbles. Then you install it.

What we routinely did at the shop was to install the master, install the brake lines finger and crack them open a half turn, fill it, pump it a few times (tightening the nut before you let up the pedal) to prime the master (catching the fluid in a shop rag) tighten the fittings and then bleed the cylinders/calipers.

It maybe only saved 5-10 minutes, but this adds up in a big shop that does 5-10 brake jobs a day. You need to do it efficiently and with no bring backs. If it didn't work or it caused returns we wouldn't have done it that way.

Bench bleeding will never hurt, but my point is that it isn't necessary and you can bleed it on the truck without recycling the fluid back into the reservoir.

yes, I see the distinction.

in all my research (here and elsewhere) "bench bleed" was seemingly generically used as a term relative to prepareing a new MC for use - whether it be on rig or in the bench vise. most people seemed to use the term for the prep of a new never used MC, not so much as exactly where it is done... so I do similar in that respect.

so in the end, we agree that it does not need to be bench bled (using the strick definiton of off the rig and in a bench vise and recycling the fluid) but that it DOES need to be bled and prepped and can been done succesfully on the rig.

Lastly, I think the confusion comes that since the term is used so loosly and generically - when one says they do not "bench bleed" it kind of implied to me that they just do not prep the MC - whether it be on or off the rig - and just hook up the system, circuits, and head to bleeding the brakes. So, now I see what 'you' meant about not bench bleeding, but we were both 'bench' bleeding the new MC in fact - just on the rig and just as succesful.
 
Last edited:
wantatlc said:
when one says they do not "bench bleed" it kind of implied to me that they just do not prep the MC - whether it be on or off the rig - and just hook up the system, circuits, and head to bleeding the brakes.

That's what it implied to me. I did minimal prep (had to do some or it didn't pump), and went at it.

Since I have to disconnect the circuits anyway, I'll look for the valves too.
 
Fast Eddy said:
That's what it implied to me. I did minimal prep (had to do some or it didn't pump), and went at it.

Since I have to disconnect the circuits anyway, I'll look for the valves too.

now that we have successfully hijacked FJ40LVR's original thread :)

I am telling ya bro - print, read, follow those steps on my link above and you will be good to go. I wrote that as a first timer myself and had awesome results and we essentially have the same setup (front disk, rear drum) though different years. I spent some time bouncing it off 1 of the big dogs here and it really should take you through it. BTW, I updated that link to have a picture of the residual valve for reference purposes.

good luck...
 
Last edited:
Plowboy said:
Checking his first post, he does have 4wdisks. On the 78 master the front cup is for the front disk axle. The rear cup was for drum. Underneath the large nut for the brake lines is a residual valve. Both front and rear have a valve. The front is a 2lb line pressure, the rear 6 lb. The rear has a higher pressure to hold the drum shoes closer to the drum as the shoes are pulled back from the drum with a spring. Remove the rear residual valve and replace with a 2lb valve and use a stock 78 proportion valve and you will have no problem. If you cannot locate a 2 lb valve and a stock proportion. Remove the 6 lb residual and install a wildwood adjustable proportion valve in the rear line. Installing a later 4 wheel disk brake master solves the master problem but will still need to install a proportion vavle of some type.

After several trials and errors, and much thanks to everyone who contributed, PLOWBOY thanks for that heads up, the situation you described makes complete sense..... The master cylinder was originally designed for the rear drums, so obviously there would be a higher pressure bias to the rear drums, and secondary pressure (lower) to the front disks! That is why my pressure is so much lower in the front output than the rear in my plumbing. My next challenge is going to be finding a 2lb rear residual. I will try TIM HILL, he seems to have everything a 40 could ever need. (anyone here in AZ with a 40 or 55 knows Tim!)
At this point my 40 is as far bastardized as possible, the brakes are the last thing left in my rebuild! (76 frame, 72 body, 78 axles, 83 engine, etc. etc. etc.)
 
FJ40LVR said:
After several trials and errors, and much thanks to everyone who contributed, PLOWBOY thanks for that heads up, the situation you described makes complete sense..... The master cylinder was originally designed for the rear drums, so obviously there would be a higher pressure bias to the rear drums, and secondary pressure (lower) to the front disks! That is why my pressure is so much lower in the front output than the rear in my plumbing. My next challenge is going to be finding a 2lb rear residual. I will try TIM HILL, he seems to have everything a 40 could ever need. (anyone here in AZ with a 40 or 55 knows Tim!)
At this point my 40 is as far bastardized as possible, the brakes are the last thing left in my rebuild! (76 frame, 72 body, 78 axles, 83 engine, etc. etc. etc.)
Is there a difference in size between the front and rear residuals? I take it that a front residual will not work in the rear. Heck, I've got three 78 MC laying around my shop. Yes, Tim Hill is the man! If everybody could see his property, you would think you had discovered the gold standard for FJ40 parts; bodies, frames, fuel tanks, trannys and transfer cases. Just about whatever you need. I asked him to let me post photos of his yard. He said he already had enough business word of mouth. You know all those rebuilt heads MAF sells, I'd tell you where they get most of them but you already know the answer.
 
Back
Top Bottom