Check 'yer nutz.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 26, 2004
Threads
233
Messages
5,819
Location
Utah
Lookit wat happens when ya doesn't.

DSC02391.jpg


The pile of poo poured out of my knuckle in LESS than 10 seconds after coming to a stop. I pulled into the driveway, got out of the truck, walked in front of the vehicle, smelled the grease/oil and looked under the truck, this picture was taken literally less then 20 seconds after parking the vehicle.

So I completely lost one knuckle stud, and at least 4 others (counting on both knuckles) are loose enough to see a gap between the nut and arm.

DSC02394.jpg


DSC02392.jpg



Price check on 8 new knuckle studs/ nuts/ washers please? I may try out Marlin's new inner axle seals as well.
 
Had it not 'let loose' I would not have known I needed a re-pack.

Yep, I didn't want to say anything but that soup has a lot of gear oil in it so your inner axle seal on that side is leaking. Might as well do both sides and get the new knuckle studs with new nuts from Cruiserdan. You'll need to replace the missing cone washers too.

The biggest problem with waiting until these "let loose" is the potentially deadly steering situation. If that knuckle comes off in heavy traffic at 70mph someone is going to get hurt.

-B-
 
Holy hell! I know what I am adding to my list of PM's this weekend. I think it's been 6 months since i checked mine last.

Is it me or does that moly grease look really green?:confused:
 
Doc,

Just got 8 sets of stud bolts, cone washers, washers, nuts for $65 from my local Mr. T. Cruiser Dan might be able to beat that, and I might have been a victim of the upcharge, but it helped me out in my urgent state. Your's looks more urgent, mainly on the side of needing a front axle job:eek:. Good luck!

Cheers,

Joel
 
https://forum.ih8mud.com/80-series-tech/229576-missing-bolts.html

11 days ago Doc. Don't you guys read these threads and learn from others?

-B-

Exactly the thread that came to my mind.

Doc,

Just got 8 sets of stud bolts, cone washers, washers, nuts for $65 from my local Mr. T. Cruiser Dan might be able to beat that, and I might have been a victim of the upcharge, but it helped me out in my urgent state. Your's looks more urgent, mainly on the side of needing a front axle job:eek:. Good luck!

Cheers,

Joel

Good job, Joel!

You really scared me with your initial post of "Can I just go down to the hardware store to replace these, and can I (I'm paraphrasing here) drive the Cruiser there to get them?" :eek:

Cheers,

Curtis
 
Dang Doc,

If I hadn't done my birf's a month ago we could have had a birf soup party together. Mine looked about the same. I would definitely check out the marlin seals. They look really beefy, but I hadn't heard about them back when I did mine.
 
They made some serious money.


That stuff just hurts. My local dealer wanted $8 EACH for knuckle studs. Cruiserdan at American Toyota wanted $1.50 each. The cone washers are spendy, even from Dan, but I got 12 of each for less than you paid for 8.
 
I don't have the FSM in front of me now, so what do you HAVE to replace once you tear the knuckle down? I'm going to replace the inner axle seal obviously, which others are non-reuse? I'm not going to replace the bearings, they have less than 40k on them since I re-built a few years back.
 
You will get an observation from a goofy parts guy about dirty underwear.

Wheel bearing repack interval is 30k. Birf service interval is 60k. That seal should have lasted 90k. Wheel bearings will last a loooong time if you repack them at 30k intervals and don't sling them across the garage and bounce them off the concrete floor.

-B-
 
I installed 8 new knuckle studs on the last birfield service. Installed with blue locktite and torqued to 50 ft/lbs using new nuts. Reused the cone washers.

-B-
 
Back
Top Bottom