Bleed brakes. The final solution ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 11, 2002
Threads
130
Messages
949
Location
twin cities
Well. Fj40 1978
Can’t figure out how to get brake pedal

1. bench bled master
2. Adjusted all drums
3. New master
4 new valves and stems with Teflon tape and grease
5. New brake fluid

still squishy.... no good

so I made a closed system looping all the brake bleeders back to the master watching the fluid move. No air bubbles and no leaks
See images

still no brakes and squishy

any final ideas before i need to take it in to a shop?

thanks

D44C9635-E151-4F89-BB9D-97B9DF3918FC.webp


CB93B9A1-8849-4E91-A5F7-22778F54C570.webp
 
booster adjustment?
 
Will try!!
 
Try adjusting the brakes till they’re tight against the drums and report back how they feel. Very often brakes need further adjustment, and this should rule out adjustment.

Another issue is that some cylinders don’t have the bleeder at the very top. In these cases the cylinder needs to be tipped to allow the air out.
 
Try adjusting the brakes till they’re tight against the drums and report back how they feel.

There are many other threads on this - you must adjust the rear shoes very tightly. Not so tightly that they smoke during your test drive, but a lot tighter than most people think. You should hear clear sounds of light rubbing when you turn the drums around by hand. If the drums were turned, adjust the shoes until you can barely slide the drums on, and then adjust them some more until you get the dragging sound.
 
Going to replace the master before cracking open the booster... will report back...
 
Try adjusting the brakes till they’re tight against the drums and report back how they feel.

There are many other threads on this - you must adjust the rear shoes very tightly. Not so tightly that they smoke during your test drive, but a lot tighter than most people think. You should hear clear sounds of light rubbing when you turn the drums around by hand. If the drums were turned, adjust the shoes until you can barely slide the drums on, and then adjust them some more until you get the dragging sound.
Yes the drums are rubbing gently
 
Adjust the booster rod like folks mentioned above and I’m sure your issue will end. Happens all the time when folks replace either master or booster and forget to check adjustment.
 
It was a bad master but still squishy but better.... will try another bleed tomorrow and if that doesn’t work then off the master will come and i will try to adjust booster
 
If squishy means spongy, then you probably still have air in the system and it needs to be bled more aggressively with higher pressure that you get with the “two person” method.

If squishy means you have to pump the pedal twice before you get a firm pedal, this means that they are adjusted too loosely. Tighten each adjuster until it locks up and then back off 2 “clicks”.
 
I'm hoping that you know to bleed the furthest cylinder from the master cylinder first, then the next closest second, then the second closest, then the closest. On my '77, the bleeding sequence is
1. DS, rear (furthest)
2. PS, rear
3. DS, front
4. PS, front (closest)

After you get the pushrod the proper length, you can check the brake pedal distance measurement in the Service Manual.

Phoenix makes a very nice one man bleeder kit. I've been using it for years, makes this process a snap. I have their full kit, but only really use the bottle.

I honestly can't understand all your hoses, as all you need is this bleeder kit.

The clear hose has a one way valve in it to stop backflow and the ends that come with the kit are top notch and fit the bleeder nipple well. I have one clear hose to run from the bleeder to the bottle that is long enough, that I can lean down and watch for the bubbles as I press the brake pedal. Just keep in mind that you need to watch the level of the reservoir of the line you are pumping, rear or front, that you don't get too low and allow in air as you pump. Good Luck.
 
Last edited:
I assume the hoses are going from each bleeder screw back up to the master. That way you can just keep pumping the brake pedal until you see no more bubbles come through the tubes. Of course if there's rust and junk in the lines it comes back through in to the master which isn't good.
 
I assume the hoses are going from each bleeder screw back up to the master. That way you can just keep pumping the brake pedal until you see no more bubbles come through the tubes. Of course if there's rust and junk in the lines it comes back through in to the master which isn't good.
Yes a closed loop
 
If squishy means spongy, then you probably still have air in the system and it needs to be bled more aggressively with higher pressure that you get with the “two person” method.

If squishy means you have to pump the pedal twice before you get a firm pedal, this means that they are adjusted too loosely. Tighten each adjuster until it locks up and then back off 2 “clicks”.
Still seems to be the former...
 
Well update:

adjusted the booster and I thought it got a little better... turns it out about 1 cm.

when stepping on the brake what kind of turbulence should be in the resvoir?
 
This is the booster adjustment SST. There are some parts store varieties out there. Are you using one like this?


What brand master is that? Also, why does your brake fluid look blue? You using DOT3?
 
It is just a cheapie from Napa. My Aisin also went bad...

I stuck a sharpie marker in the bottle of fluid to dye it so I could tell old from new. ...

I will try that tool
 
Back
Top Bottom