Bare 1FZ block weight

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

It isn't a huge deal, I was just curious. The billet aluminum LS blocks are around 80lbs and hold 2000+ hp. I was just off in my own little wonderland wondering what a 1FE iron would weigh compared to a 1FZ billet aluminum. I have said multiple times I think TLC4x4/ICON is kind of copping out just throwing an LS in their trucks when it would be really awesome to see what a current high tech 1FZ would look like. They sell billet blocks for RB30's and are only about $9k.....

Imagine a 1FZ with:
Aluminum block
Higher compression pistons and light forged rods
Coil on plug ignition
Good intake and exhaust manifolds
Drive-By-Wire throttle

Yes there would be substantial cost to dial it in, but it would very cool. I mean I basically will have everything on the list except the block for my turbo build, but I think it would be awesome to drop a couple hundred pounds and do a 300hp+ naturally aspirated new era 1FZ


13912913_657847574378308_9064001937465005104_n.webp


I have a bare block sitting in the yard but no scale that the wife would let me set it on. I've moved it around a few time by myself and it's not fun. Mostly dragging or lifting to move a foot at a time.
 
Last edited:
While I get you on 'Yota platform companies running a update motor, you also hit on the average Joe's reason for an LSx - $9K. For the block.

Thats 75-80% what my crate LS3 was with all the marine spec goods like H.P. fuel pump & OBD-M harness & idiot cluster for the dash (new, marinized conversion from Kodiak) - let alone what guys pick up used ones for now that even a LSA is getting availability from breaking yards. LS3's are now almost dime/dozen thanks to wadded up Camaros & Caddys.

If the Supra sold like Camaros maybe we would have guys going nuts with those motors, but it seems like a turbo Supra was a harder sell than a 80 series in 1996-97, from what I remember. We didn't see many of them here in WA, that's for sure!
 
Scotty, I don't know what a bare iron block weighs but I guarantee it would make one hell of an effective paper weight.

I also agree with the TLCA/Icon statement. For the cost of one of those trucks I'd want a Toyota drivetrain under a Toyota body. Dana axles don't look right. If you can afford a 150K+ truck the price really no longer matters.
 
Yeah, I know LS engines are great, but in the 60's-70's-80's when people fell in love with Toyota it was because they were so much better than the domestic counterparts. In todays car landscape, Domestic quality has improved and Toyota quality has declined, so they kind of occupy the same area.

But if TLC/ICON did something like this, and created a newly modern TOYOTA inline 6 cylinder, with all the technology available I would bet you could see a 300-350+hp NA engine thats <500lb. Hell you could swap it into 40's, 55's, 60's 62's, and 80's. And it would be a very important crown jewel when you opened the hood. It wouldn't be a V8 that said corvette on the valve covers sitting in a 40. lol.


And it's really not that far fetched. Today there are plenty of ECU's that give us way more control than Toyota ever had in the 80's developing the 1FZ. Using wideband O2's vs stock narrow band, adding a crank trigger and using coil on plug for precise ignition timing, better atomizing injectors, etc. Not only with regards to power but also fuel economy. The OBDII 80's run very rich like 10:1 in; open loop, before the coolant temps come up to temp, when at WOT, in heavy load cells, etc but that could be dialed way back as far as 12.5:1 in no load very low load you could run lean like today's cars at 15:1, etc.

And yes all of this could be done on a stock block, but I was day dreaming. Lol




Scotty, I don't know what a bare iron block weighs but I guarantee it would make one hell of an effective paper weight.

I also agree with the TLCA/Icon statement. For the cost of one of those trucks I'd want a Toyota drivetrain under a Toyota body. Dana axles don't look right. If you can afford a 150K+ truck the price really no longer matters.
 
Last edited:
Agree - no chance I pull my 1FZ out of the black 80, ever. Has ~135K, no reason to.

My 40th has 368K & only popped a HG 30K ago, all it needed was a gasket & stem seals per Robbie.

I get the why of an LSx motor for a guy who has a rod through a block, but for my personal use I won't pull a 1FZ that is great for my use - I am great with the torque of a 1FZ sans even a S/C, so swapping in a LSx is taking a grenade launcher to a sub-MOA match for me.

And when you have a LSx & Dana axles, you start to get to a point where you like the cabin but have really modded the drivetrain - A Suburba-Cruiser if you will.
 
i would be fine with the iron block, the problem with the 1FZ is the head design. thats the part you would need to update to make any real power.
 
What's wrong with the head design? On a flow bench it out flows a 2JZ which routinely make 1600hp. When I called Headgames about doing my head to run up to 1200hp, they said the stock head can do it, don't even bother touching it for that little hp.
IMG_2092.webp



i would be fine with the iron block, the problem with the 1FZ is the head design. thats the part you would need to update to make any real power.
 
No solid numbers for you here. I sent a short block with no rotating assembly to the machine shop two years ago. I remember thinking I could carry it myself if it was already up off the ground. At the shop me and another guy just slid it over onto the tailgate and lifted it onto a cart. I would say maybe 200# at the high end.
 
yeah it flows fine for boost but that is another issue. once you start talking boost then you get into another area that sucks for toyota, the ECM. time for a piggy back or stand alone, then you need to manual swap or get a stand alone trans controller. you cant make good NA power out of the I6.

i keep my 1FZ stock because it just works and gives me no reason to mod it... yet. it is a fantastic engine for what it is but a power house it is not. if you want power there is no reason not to go LSx. i am also in the middle of building a 5.3 to replace my 2JZ because it is more power per $.

i have an 80 that is 100% factory and will stay that way. i also have a play toy that is modded like crazy. if you are willing to butcher Mr Ts suspension, radio, bumpers, gearing, lights, and more then why not the engine?
 
Just carried mine from the truck to the mechanic. Not more than 175lb. Either that or I am killer strong!
 
Scotty, I don't know what a bare iron block weighs but I guarantee it would make one hell of an effective paper weight.

I also agree with the TLCA/Icon statement. For the cost of one of those trucks I'd want a Toyota drivetrain under a Toyota body. Dana axles don't look right. If you can afford a 150K+ truck the price really no longer matters.

Or a coffe table @jfz80
 
Hey now..... thats not fair, insider secrets an all posting as you already got the intel. Some of us are long winded.... esp after lugging a block around the house for accurate readings. ;)

Man I wanted to call BS on that, turns out im just not as beast as the @Comet ;)

And he may have nailed it. Prize?

Less speculation but still not exact. I couldnt believe it myself! Granted this has 4 main caps and 4 3/4 pistons attached :lol: and theres the factor of it being a less than precision quality instrument. However if someone proves it off then it'll be available in classifieds for purchase for the lil lady in your life to make everyone happy.

Weighed it 3 times and got the same. It reads reasonably accurate for my weight vs a balance scale at the doc's office.

Thats an awful expensive price tag to shed a very few pounds. (Ok more of a savings after second set of readings)

I know you and this project isnt necessarily about the need vs the want (or the cause it can be done) so carry on. Just reminded me of the response to your head flow question you just posted.

IMG_9740.webp
IMG_9744.webp
 
Last edited:
I was a little emotionally crushed and headed to the gym after the first (INACCURATE) attempt on carpet. Now i feel better...... and got my workout in :grinpimp:

IMG_9742.webp


@fj40z give me a ring after work.... i need a hand with something :flipoff2:
 
Last edited:
I would have felt better about moving it again not knowing what it weighed! At least before I thought I was moving a lot more weight, now it just makes me feel weak.
 
I would have felt better about moving it again not knowing what it weighed! At least before I thought I was moving a lot more weight, now it just makes me feel weak.
I'm with you on that. I'm emotionally beaten by that scale. I can't brag about moving it myself anymore.
 
I was a little emotionally crushed and headed to the gym after the first attempt on carpet. Now i feel better...... and got my workout in :grinpimp:

View attachment 1375587

@fj40z give me a ring after work.... i need a hand with something :flipoff2:
What are you using that block for?
 
Must have been an "on" day. Normally, I cant even pick up my own shadow. Ha ha!!!
 
Haha awesome! Well there is some pretty solid proof it looks like that it is around 175lbs. After doing a little more digging I found that a 6.0 iron block weighs 217lbs and in aluminum form weighs around 106lbs so doing some incredibly rudimentary deductive reasoning. a 175lbs iron block could weigh about 85lbs so a savings of 90lbs. Yeah that is an awfully poor return if the block is around $9000/90lbs = $100/lb. Too rich for me. lol.
 
Back
Top Bottom