auxiliary fuse block

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 30, 2005
Threads
11
Messages
67
Location
Tunica, Ms
I wanted a seperate fuse block for all of my accessories (arb's, radio xm, lights, cb, ect). Does any body use one? If so what kind?

I did a search and came up with one from Waytek. Do not know what type? Also found one from painless. It looked like what I was looking for just pricey.

If thier are any other ideas I would like to hear them.
Thanks

Wayek


attachment.php


Painless
70207.jpg
 
I use the ones from Waytek in a lot of projects. They work well, but be aware of one issue: They do not come with a dust/water splash cover. Check out the ones from Blue Sea Systems. www.bluesea.com They are a marine supplier and offer some of the coolest fuse panels you will find. They have covers complete with changeable slide in labels. Check out part # 5026 it's a 12 circuit panel with a ground buss. More expensive than the Waytek one but a MUCH better panel.
 
Poser we both must really like Waytek parts! I currently have the one in the top LEFT of that page in my Nissan Xterra. It was originally to be used for a customer but he backed out of the project. So I naturally incorporated it in my truck. It has a nice cover for it and I used a Radio Shack cheap plastic box to mount it in. Bit too expensive though since you have to buy the terminals and install them yourself. Came to over $35.00. (which the customer did pay though he backed out on installing it.)
 
Coolerman said:
I use the ones from Waytek in a lot of projects. They work well, but be aware of one issue: They do not come with a dust/water splash cover. Check out the ones from Blue Sea Systems. www.bluesea.com They are a marine supplier and offer some of the coolest fuse panels you will find. They have covers complete with changeable slide in labels. Check out part # 5026 it's a 12 circuit panel with a ground buss. More expensive than the Waytek one but a MUCH better panel.


Bluesea has some seriously great fuse boxes. I've had mine in for a year or two in a Tacoma......it looks clean, cover doesn't shake loose. I haven't seen any better ones out there. I bought the 12 slot version with the negative bus.....but they make them in several sizes, with and without grounds. :cheers:
 
There is not anything else that I have found that is as nice. I have no interest in installing a pre-made harness, and then splicing s*** right out of the box. The fact that they offer terminals to connect to the wire that will plug right in the back of that is a great feature. Most things that are of decent quality are not inexpensive, this is true anyplace, but especially with this sport/hobby.

I have made a metal bracket that the fuse box attaches to, and then that attaches to the inner A pillar on the passenger side of the truck....simialr to the stock location of the fuse panel on 1971 and later 40's.



:beer:
 
I'm almost to this point in my project. Consider the number of positions that are "hot always" as opposed to "ignition hot only" and what you want to run off the fuse block. You might also want a thermal breaker in-line with the aux power main, this could save some grief down the line by protecting the main power connect cable from melt down.
 
Do the waytek and the Bluesea fuse blocks have relays. Is a relay even necessary? I called waytek today ,but they were not much help. They only gave me page numbers of where the fuses were. I thank you for the help.
 
some PO installed a secondary fuseblock in my truck in the engine compartment on the firewall passenger side, it looks very similar to your top picture, but has more substantial ground posts; it is always hot, and I run accessories off it that I may want to operate when the ignition is off: rock lights, stereo, CB, ARB compressor etc. It has 14 positions, and that is in addition to the 12 circuit fuseblock which is inside by the driver side footwell mounted on homefabbed bracket in the stock location. Most circuits have relays (which are mounted on the insides of the fender aprons). By the biggest accessory fuseblock you can afford/fit and support electrically; I found that the positions were used up real fast and you will always find more uses to hook up.
 
rusty_tlc said:
You might also want a thermal breaker in-line with the aux power main, this could save some grief down the line by protecting the main power connect cable from melt down.



High amp fuses I have a 200A feeding the aux fuse panel I installed.

I do not have any switched power spots on that panel, as I like things hot, and not dependent on a key...


:beer:
 
ram said:
Is a relay even necessary?


If you are looking to reliably control more than 10 amps, I would install a relay, without question, unless you have some very stout, high quality switches designed for higher amperage.


:beer:
 
I made this one when I rewired my 40 with parts from WayTek...it's not quite finished in this pic, but you get the idea....
image0001.webp
 
LilRicky said:
I made this one when I rewired my 40 with parts from WayTek...it's not quite finished in this pic, but you get the idea....



Like the Dzus fasteners for the cover.....looks nice!


Post up a pic of the cover.


:beer:
 
Poser said:
If you are looking to reliably control more than 10 amps, I would install a relay, without question, unless you have some very stout, high quality switches designed for higher amperage.


:beer:
You also get the advantage of using a lighter guage wire to the control the relay. So for instance you can run 22 AWG (7 amps) to a relay that controls a load that requires an 8 AWG (73 amps). It's a lot easier to route 22 AWG through a fire wall to a dash switch and back to a light relay than 8AWG directly from buss to switch and back to lights. Never mind the voltage drop from running that much wire.
 
If you really want a cheap fuse block that is great quality and don't mind a bit of fabrication use this one: http://tinyurl.com/lq7rh Gives you 9 ATC fuses, 1/4" connectors for the accessories and scew downs for the input side. I bought one to use in the Cruiser when I get to that stage.
 
ram said:
I did a search and came up with one from Waytek. Do not know what type? Also found one from painless. It looked like what I was looking for just pricey.

If thier are any other ideas I would like to hear them.
Thanks

Wayek

The junk yard is full of nice fuse blocks and mini relays that look like that and they only want a few $ for them.
 
I like the idea of it being put togeather with the relays and fuses. Since i am new to the rewiring and do not know what to order or how to put it together.

Thanks for all the advise.

I'll try a junkyard and see what I come up with.
 
Back
Top Bottom