Adding extra LED to doorjam switch?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 2, 2003
Threads
152
Messages
5,766
Location
Syracuse, Utah
Has anyone tapped into the doorjam switches for the dome lights and added additional lights? I'd like to add a light to the front seat area so that the front gets illuminated when the front door opens in addition to the second row.

I've heard of some trying to wire the front map light to illuminate with the door switch but I'm thinking of leaving that one alone and adding a small light just above the top of both front doors.

Ideas?
 
May as well install front and back of both front seats to illuminate all foot wells.

Awaiting your progress.
 
illuminate all foot wells.

This is what I was going to do. If I remember the plunger in the door jam takes it to ground. I was going to find a good hot above the drivers and passengers feet and then tie to the plunger
as the ground. It should work, but I haven't dug in yet. Its on my short list to do relatively soon so I can post back my findings. I am going to use these - they have some double sided tape on the back.
Screen Shot 2018-11-28 at 6.40.59 PM.webp
 
The L&R front door switches are isolated with diodes. If you want both front doors to activate the additional light(s), you'd have to tap into the dome light wires. The 6-pin "IE1" connector in the driver's side A-pillar would be a good spot.

Pin-2 (BLUE/YELLOW) for hot.
Pin-3 (RED/BLUE) for switched ground.
 
The L&R front door switches are isolated with diodes. If you want both front doors to activate the additional light(s), you'd have to tap into the dome light wires. The 6-pin "IE1" connector in the driver's side A-pillar would be a good spot.

Pin-2 (BLUE/YELLOW) for hot.
Pin-3 (RED/BLUE) for switched ground.
Thanks for this. Any chance you have a photo of the connector you referenced? Just so I know what to look for.
 
Thanks for this. Any chance you have a photo of the connector you referenced? Just so I know what to look for.
No photo at the moment, but behind the driver side kick panel there is an access hole below the A-pillar. Fish out the bundle of wires, there will be 3 connectors. There is only one connector with six pins. HTH.
 
This is what I was going to do. If I remember the plunger in the door jam takes it to ground. I was going to find a good hot above the drivers and passengers feet and then tie to the plunger
as the ground. It should work, but I haven't dug in yet. Its on my short list to do relatively soon so I can post back my findings. I am going to use these - they have some double sided tape on the back.View attachment 1842084
where did you grab those lil babies??
 
I know this is not the exact location you are looking for; but I added a flush mount LED in the door card to light up the footwells, lower dash and center console when the doors are opened. It works well for finding dropped items on the floor. I just tapped into the existing door light.
door light open.webp


door light night.webp


Flush LED.webp


Between these door lights and LEDs in the second row dome I didn't feel a need to have the moonroof dome lit with the front doors.
 
The L&R front door switches are isolated with diodes. If you want both front doors to activate the additional light(s), you'd have to tap into the dome light wires. The 6-pin "IE1" connector in the driver's side A-pillar would be a good spot.

Pin-2 (BLUE/YELLOW) for hot.
Pin-3 (RED/BLUE) for switched ground.
Am I understanding this correctly? Tapping into the Blue/yellow for hot from the new light, and the ground wire from the new light to get tapped into the red/blue for switched ground? I tried that with no success. There is power to the blue/yellow but apparently the red/blue is grounding correctly for the new lights to work.
 
Tapping into the Blue/yellow for hot from the new light, and the ground wire from the new light to get tapped into the red/blue for switched ground?
That should be right. Your new light will be wired in parallel to the overhead light with this setup.

Is the new light an LED? Have you confirmed polarity?

...but apparently the red/blue is grounding correctly for the new lights to work.
Should that read "is grounding"? Or "isn't grounding" correctly?

With the door open, the RED/BLUE wire should read 0.7 Volts. Measuring continuity to ground won't work due to the isolation diode.
 
That should be right. Your new light will be wired in parallel to the overhead light with this setup.

Is the new light an LED? Have you confirmed polarity?


Should that read "is grounding"? Or "isn't grounding" correctly?

With the door open, the RED/BLUE wire should read 0.7 Volts. Measuring continuity to ground won't work due to the isolation diode.
Thanks. I was a bit short on time when I worked on it earlier. I haven’t used a volt meter to check voltage yet, and I’ll do that when I can get back at it.

My mistake on the misspelling. I did mean it “is not” grounding correctly.

Also have not checked polarity on the LED. Good suggestion.

I’ll let you know how things go. Thanks again.
 
Shipwreck, those are supper slick. I'd been looking at those little fish-eye bulbs trying to figure out what to do with them. I was thinking they would work well around the rim of the hatch for work lights. The foot-well-light idea is excellent.
 
Finally settled on a solution yesterday. I know others have done different things but I found a simple little LED at the local parts store that fit very well right on the "foot" of the rear view mirror. I tapped the wires into the harness for the small lights on the doors that come on when the door opens. Works great and now I have a nice bright cabin in the front as well as the second and third rows. I already have PFran LEDs in the overhead map light and in the rear dome light. My 2nd row dome lights are incorporated into my overhead DVD player. All of them come on when any door is opened.
DomeLights and Struts by Adam Tolman, on Flickr

DomeLights and Struts by Adam Tolman, on Flickr

DomeLights and Struts by Adam Tolman, on Flickr

DomeLights and Struts by Adam Tolman, on Flickr
 
Back
Top Bottom