upper control arm

While browsing UCA for 2005 GX470 and knowing that the 5th gen to 23 4runner has same UCA, I discovered on rock auto that 2004,2005 4runner 6 and 8 cyl both use the same UCA as the gx470 and 23 4runner.

Hey all, Had a half successful half frustrating day today while trying to replace my stock upper control arms with SPC arms. I started on the passenger side, I used a 5 ton puller which wouldn't make the ball joint budge, then I can't tell you how many times I hit the damn ball joint with my...

Ok, relative 100 LC newbie here...I am currently working on baselining my new to me 2006 LC. It currently has OME suspension with heavy rear springs, SPC Arms, Slee front diff drop, Trail Tailor extended links, and the Delta VS panhard bar bracket. I have replaced the upper ball joints in the...

Hi All, I've had Pro Forge Upper Control Arms in my 200 Series for about 18 months. One of the ball joints seems to be a bit "loose". The castle nut is tight, and the split pin position is fine, but it makes a little clunk when turning hard right, and I can feel the looseness in the wheel when...

I’m looking for upper and lower control arm tundra ( total chaos or icon ) thankyou

Hey guys, I've got a stack of suspension parts purchased for a 100 series that got totaled unfortunately. They were never installed and they're all still in their boxes. It was a big loss. All prices are negotiable but they are already much lower than what they set me back. They also...

Maybe a dumb question, but how can you tell when your upper control arm bushings go bad? I am replacing my upper ball joints (which are completely shot) but they just won’t press out. I am pretty frustrated and considering now just going for entirely new UCAs since if I pull the current UCAs...

Working on pressing out my front end bushings/ball joints and all went well until the upper control arms. Working on the first one and I was pressing it in a not so great way and it didn't work. So I release the pressure and started looking at how I could make it better and I noticed a gap in...

Hey guys, Got a set of Nitro upper control arms brand new in the box for the 100 series. Asking $600. PM me if interested.

Hey guys I've got a set of brand new Nitro Upper Control arms still in the box. Asking $600 and open to offers. Thanks -James

Hey guys, Looking for a set of SPC racing UCAs for my dad's 98 lc. PM me if you've got a pair or know someone who might. Thanks James

Hey guys I'm looking for a pair of SPC light racing UCAs for my 98 lc. PM me if you've got one for sale or know someone who does. I've also got a brand new pair of Nitro upper control arms still in the box that I would be willing to trade. They're stronger that the SPCs but I'm lifted high...

Bought a set of Nitro ucas from Carl at Just Differentials about 3 months ago. Paid $750 plus shipping for them. I'm 20 years old and in college trying to build up my dad's 1998 lc. But my sister's just had some major transmission problems in her car and I'm selling these arms to help me...

I tried searching, just found threads on upper front A arms. I am looking for adjustable REAR upper control arms for my 200. Ideally adjustable on vehicle and with OEM style rubber bushings. Does anybody know of any? Would adjustable 80 arms work?

So there are a few reasons I am not very happy with my lift but two I was really not expecting this to be an issue since so many FJ's, 4Runner's, and now GX's have already been lifted. Lift Installed Used/Re-built 2.5 ICON Extended Travel Coilovers SPC Upper Control Arms Used 2" RadFlow Coil...

I have these front shocks and upper control arms I have been hauling around for 5 years from a build I did on an '06 Tundra. Free for local pickup. I am in the San Francisco Bay Area.

I've read several threads where folks talk about running +3 (D) or +4 (C) degrees caster and the merits of each. I'm installing these upper control arms this weekend and am wondering what folks are happily running, assuming 2-3" lift (50-70mm droop), diff drop, upgraded shocks and torsion...

Last time I went out my upper control arm was loose and slapping around. We torqued it down and it got better, but still rattling when it gets a little rough. I haven't dealt with this before. Do I just need to replace that bushing or what's the next step for proper inspection and replacement?

Who's running what and any feedback? My OEM bushings are worn out, so I figure it's time to upgrade. Looking for some first hand opinions!