timing

Have a 91 with a 1hdt. Currently in the middle of pulling my old injection pump out b4 putting in an upgraded one, was lining up the timing marks and the 2 timing belt pulleys line right up with the marks but the crankshaft is slightly off of its mark. Never had a noticeable issue with the...

sorry: posted in wrong forum. Please delete this topic

Hello, While replacing the head gasket on my 1fz-fe I dropped a 8mm washer into the timing chain cover. I removed the crank position sensor and can see the washer from there. The washer is sitting at the bottom of the timing cover just forward of the crank position gear. I have been unable to...

Trying to find a good Land Cruiser mechanic to perform timing belt/water pump service on 2005 UZJ100. Any recommendations? Preferably in the South Bay/Harbor City area. Thanks.

Getting a timing cover leak on my Land cruiser... garage saying it'll cost $9K AUD as engine needs removed due to how timing cover sits sandwiched rather than bolted in. any advice on how easy this is to do by self?

Came off a B-series engine, I think 3B but can’t remember exactly. No idea on compatiblility. $20 plus shipping. Can vapor hone it and make it beautiful for $20 additional

Hey yall! Long story short: overheated my 07 100 series, radiator blew, head gasket blew, replaced all of it (by the book(FSM)), immediately had rough idle on start up, only in drive and reverse at idle letting off brake, everything was solid enough to load up 3k pound trailer and drive 21...

When adjusting timing using a timing light with an advance function, do you set the advance to zero and adjust the timing to the BB to get 7 degrees advance? If you want to try 10 degrees do you set the advance function to 3 degrees and time back to the BB (or set to 10 degrees and time to TDC...

My right cam does not line up perfectly. It is very close but not right on. Will this be ok?OK? Note the pictures.

Searching for a clean timing cover to fit a 1982 2F engine.

Just had my heads redone, replace timing belt and all but now it runs really bad. and all but now it runs really bad. I’ve checked and double checked it’s not a simple jump the tooth… Would love to be able to call right now since I’m trying to get it away from where it’s parked tonight!

Hey everyone! Does anyone else have a crank pulley that doesn’t line up exact even though the other 3 marks are lined up? (Oil pump dot and both cams) I checked and rechecked before pulling the pin. Rotated the motor a ton by hand and the 3 marks still line up but the pulley doesn’t show 0...

Or at least do a partial disassembly/inspection. Here's the OEM water pump I bought from the dealer last time. 140k miles on it, had been leaking for awhile with no signs elsewhere. The thermostat housing groove is perfect for an o-ring, 2-034, stays put in the groove with a little goop...

I did the tappet cover gasket on my 2F this weekend including pulling the distributor out. I made sure to put the distributor back in the same rotor position as when I pulled it out. I did not have a timing light on hand to verify timing, so I adjusted it by ear and set it at the smoothest...

Hi all, I just collected Mister Blue, a 2003 105, to daily for a week or two before it goes back in. I parked the truck right after inspection and registration for fear of a timing belt failure. This poor old truck has been out in the UAE sun for a long time and all the rubber has gone bad...

Got my newly rebuilt engine running, and noticed a slow drip coming from the timing cover area. There was a mix of coolant and oil, and after confriming the Hose of death on the underside of the waterpump was leaking ( PN 90910-05155) I assumed this was my only issue. I tightened a clamp and it...

Hi All, we are new here, My 1998 LC Beulah has busted her timing belt and my mechanic isn't interested in replacing it, he says "it's too old"...! He doesn't know Beulah for the last 15 yrs like I do. It's a love affair really and now both of our hearts are broken. She does have 330K mi. on...

I've attempted to find the timing procedure specific to a 1977 CA Spec Distributor. The link below indicates that I have a CA Spec (Advance + Retard vacuum ports) on my distributor. I'll attach a photo of it as a reply to this thread below. 1) When setting timing, do I disconnect (& Plug)...

This is how I have my distributor set, I'm afraid that I have it a tooth off on the cam. 83 Fj60 dizzy and flywheel on a 1.5f don't really know if that makes too much of a difference

In the process of doing my timing belt, ordered all the genuine bits and I noticed there is a change in the backing plate behind the timing belt Tenensioner. The original one had 2 holes that lined up to the dowels on the timing cover and the new one only has one hole. The new one fits but the...