Hi group . I have a 1997 lx450 and I was wondering if anyone makes a subwoofer speaker enclosure that fits in the passenger rear side panel . I 'm looking for something that will fit in that space . I don't mind if the plastic panel is cut out f the way to make it fit . Whats some...
Hello recently purchased this fj defiantly has cool patina but also so series rust and 30 year old bond I am looking to either leave it alone or a quick cover up until I can do metal work properly at least 3 to 5 years away. NOT A 100 opposed to diamond plate quarters but reluctant...
This switch panel has been on my desk at work for about 10 years when it was removed from a part out. I’m certain the partout was a 3FE so this is an FJ80 panel not an FZJ.
$140 shipped to the lower 48.
Selling 1 Kanon molle window panel for the passenger rear inside of a 200 series. All necessary hardware included. Including the captive nuts to the headliner.
$100 plus shipping, ready to go.
So I've ordered a set of Rhinohide Armor panels and they will not work with the stock lower door trim panels. My options are trim the Rhinohide panels or pull the OEM lower trim panels off. If I do the later, I'll be looking at this:
So how to best fill the holes? There is no easy access to...
This is the piece that holds the ignition switch and several other switches including the locker switch. Very nice gray panel unmolested only switch included is the dimmer switch for dash lights. Price $28 plus shipping. Best to email me shmukter@pa.metrocast.net
Now that I've got everything baselined mechanically, I'm trying to do some small interior stuff.
Does anyone know the name (or part number) for the trim piece that sits between the overhead light and switch panel and the headliner?
It seems as though a prior owner installed a tan part instead...
Selling a 1 year old iKamper 3.0 with a Merlin solar hawk 110watt solar panel. Tent has some inevitable sun fade on the top but the inside looks, functions and smells like new. Top has had fade buffed out once and looked brand new. Could possibly try it again or vinyl wrap the top.
The ikamper...
Hey Everybody,
I want to replace the speakers of my 1987 FJ60 with the JL Audio C2-525X (5 1/4 inch) for the front doors and back panels. I also want to buy the rear Orikawa panels to replace my OEM back interior panels. Normally, I am not a big fan of aftermarket parts like this. However, they...
I want to remove the lower door moldings on all 4 doors. I found this good video in @brandonb4 's chrome delete thread but it is for MY 2016+. My 200 is a 2015 and the moldings are different. I do not know for sure if they are clipped on in a similar way or not. I have heard that some MYs...
Hey all,
I can't believe I am going to ask this dumb question but does any one have any photos on how to install the drivers side kick panel and dead pedal? I found the part where the panel clips in to the firewall with that special clip but I can't tell if the dead pedal goes under the kicker...
Hey all, anyone have experience fixing body rust or rust in this specific area and can help walk me through how I can repair this? I have a welder and I did a simple repair of some rust in this area already with some sheet metal and some screws/silicone to seal up the opening into the body...
How does this instrument panel work? It was imported to Brazil until 1967, then it was nationalized, I want to know how the temperature and fuel, ohmic range and power supply work
Did a search and found a few thoughts on this topic but I am still a bit confused. Wiring does this to me lately
the original dash panel has been replaced but the ammeter is not doing anything so opening it up reveals the wiring shorted together and I assume, as a bypass. Battery charges at...
Howdy
How do you remove the access panel where the radio is mounted too. I see 5 screws on the face which I have removed , but uncertain on next step. Does it pivot down or slide out?
Thanks
Ernie
Has anyone removed the interior panel on the lower tailgate (2013 LC)? I dented the lower tailgate a bit and believe I can improve the size of the dent if I can get in there. Tried removing the four screws under the cover, but with the panel not moving at all I thought I'd ask here before...