Pulled the oil pan on my 91 FJ80 with the 3FE to finally tackle the oil leaks! Valve cover and pushrod cover have been done so this was next on the list.
Pulled the pan off and noticed the paint on the left side was pretty bubbly. Got to working on the wire wheel and found a few small spots...
Hello I've been looking for an oil pan for my 92 land cruiser fj80 4.0 and every place I look they are discontinued, any idea where I can get one I also need a gas tank.
Thanks
I have the following parts available:
Jump Seat Covers: SOLD
Unsure of the make, they were on the seat frames when I purchased them
Used Slave Cylinder: $10 + ship
I believe it's in good working order; it was replaced as I troubleshooted my clutch which turned out to be a bad Master...
I switched over to a 2F valve cover and no longer need this brand new gasket.
Anybody want it? I'm also gonna buy a side lifter panel gasket and oil pan gasket if someone wants to trade.
Thanks!
I'm trying to copy anothernord and swap a 1kz-te into my 2001 Tacoma and I foolishly got a motor from a Hiace Regius instead of a Hilux so the oil pan hits the front differential. I know I should order the correct pan but it is going to be over $500 from Japan so my current idea is to flip the...
Hello mudders. A buddy and I are working on the rear arch seal (among many other things) on an 97 Land Cruiser I bought recently. I’m having a hard time identifying the proper name (and how to search for) this o-ring located in the block facing the upper oil pan directly behind the oil pump. I’m...
Hi, here's context: I'm rebuilding a 5/1973 F engine. Old oil pump is discontinued, so I had to fabricate a new oil pump output line to make the new style oil pump fit. The new custom line fits great into the threaded hole, but there is another threaded hole next to it, and I cannot figure out...
Hi. My natural instinct is yes, I do need a new oil pump. But I have a 5/73 F engine and can no longer get a new oil pump because they're discontinued.
I suppose I could upgrade to a 2F oil pump, but I've heard that I would need to get a 2F oil pan too.
What are my options? Can I just reuse...
Hi. Does anyone have the bolt sizes for the oil pan and side cover bolts? Also looking for those three bolts that hold the steering column to the firewall.
Thank you.
There is an issue! Oil change shop stripped the drain plug so it currently cannot accept a bolt. I thought that someone might be able to modify/repair it instead of me tossing it in the trash. It is steel.
Free to the first person who claims it and is willing to pay actual shipping. It...
So I'm confused by all the oil pan part numbers out there. I have a '71 with the original F motor. According to toyotapartsdeal.com I need part number 12100-60060 which has been replaced with part 12101-61013. BUT, when I search the newer part number, it seems like that one is for later 2F...
I got this oil pan with a 64 FJ40 project I parted a few years ago. It's very solid these are no longer available. Has the big diameter drain plug. Price $100 buyer pays shipping. Best to email me shmukter@pa.metrocast.net
Hello
I purchased a 97 lx450 a few months ago with all the normal oil leaks. Thanks to Mud I was able to fix all but one last leak. The last one was the oil pan arch /rear main seal leak. Oil was on the bell housing. Thinking the oil pan arch was the cause of the leak, I went that route to see...
So i ordered a 2.4LTE received it and it was out of a hiace van. long story short the oil pan will interfere with my front axle. im needing one that will fit with its own built in dipstick.
let me know what ya got
801-564-9029 Ryan
Just doing the timing chain on my 1989 22r engine. My book says to lift the engine about 1 inch and pull it out. I tried that - no go- lifted it over 2 inches and still no where close. It doesn't even seem like I will be able to lift it high enough to get it out. Does it have to twist out...
I have a 1HZ oil pan to valve cover engine core I purchased 4 years ago with the intent to rebuild. Reality has caught up to me and I now realize I have too many other priorities. I can assist with shipping but the details and cost needs to handled by the buyer. I had it shipped from TN to NH...
So I need to replace my 97's oil pan gasket and I'm a bit confused on the part number. It appears to be 12151-61011, but that part seems to be from 91 to 93. Can anyone confirm?
Thanks,
Dan