hub

For those of you with 2016+ LX570s. Can you do me a favor? wiggle your center caps around, are they loose and move around? Or are they tight and firm? All 4 of mine wiggle around. I have removed them, inspected, no broken clips, they all look fine, but they still are loose when installed. -

I was doing some searching found a few fan clutches out of 93-94 vehicles, but wanted to see if anyone had the “black hub” model number or part number to reference? There is a parts truck here locally wanted to make sure it was the right one n reference photos. Or if any has the aussy model...

I’m having a heck of a time getting the preload dialed in. Long story short…. Completely rebuilt the knuckles… set the preload like the manual says, works smooth with 3lbs. When I put the locking nut on and set to 58ft lbs, now the preload is around 9-10 ft Lbs and out of spec. One printout I...

Hello, I have a frankentruck that I'm dealing with, and it appears to have a full floating rear axle (it's an fj45) but heavily modified and not in a good way. I need brake discs for the rear, but it seems that the center hole in the disc is appx. 4.5 inches in diameter... I've tried multiple 4x...

I'm finishing up a rebuild on my front hub, and I'm at the point of adding the thrust/claw washer then the nuts. I tried spinning the brake disc to check how much resistance there is and to spread the bearing grease about, but now I'm concerned about how much there should be after coming this...

Can someone look at this picture and tell me if this left front hub is set to 2 wheel drive. I think it is but I just want to be sure. The indicator markings were scraped off when I bought the vehicle. I've looked at the right front hub and it seems to have the same setting. My front...

Hey guys, new to the Mud so just posting this here for some help. I have a HJ75 ute .2 days ago while driving all the studs on the right rear hub sheared off , luckily didn't lose the shaft, wheel or anything else that would've wanted to come off then. I cannot figure out why it sheared off...

Does Anyone have one of these laying around before I order one? Thanks in advance.

I have a used set of front hub and bearings that a customer wanted to have replaced. hubs and bearings have 200k miles on them, there were no issues with the wheel bearings when they were removed. hubs are in good condition as is the abs ring. p/n is 43503-69035 asking 100 for both, they are...

I began the process of installing new pads and rotors on my 94’ fzj80 today(not manual locking hubs). I am unclear on the torque specs and order on installing hub components and the hub itself(rookie mistake on my part) and my haynes manual isnt giving me the info i need. When reinstalling my...

Hi guys, In the middle of my Birf//hub/diff rebuild & wondering how much is too much wear. Images show typical wear on star. Ball & housing look good... What do you think? Money is tight so I was thinking to swap sides but don't want to be stupid since I came this far... Also, axle seals were...

New in box, never mounted, Motorsport Tech wheel spacers for 100 series front hubs. 10mm thick 5x150 bolt pattern in ALUMINUM. Commonly used to allow fitment of rock warrior or similar aftermarket wheels. I bought for this reason, but have since sold the wheels. I paid $95 with shipping and...

Coarse spline birfields Coarse spline Warn hub Coarse spline Selecrtro hub Hubs unlock and lock by hand but have not been gone through. $50 shipped CONUS

Hello all, I am looking for a trustworthy service shop in the Jacksonville, Florida area. My vehicle is a 2006 LX 470, and I want to have the front hubs, CV, brakes (rotors, pads, fluid) fully serviced. I typically do this stuff myself, but just don't have the time right now. I am going to...

Well, this may seem like a stupid question to many and I have a good idea as to the correct answer but I guess I'm just looking for some general agreement or disagreement with my thoughts. I'm putting my drivers side hub back together after new bearings, new ceramic pads and freshly resurfaced...

Hello every one! Few months ago I replaced the bearings on front axle hub, recently it started making kind of humming noise. So I decided to check the grease in the bearings and also tighten up the hub adjusting nut. But two of the studs that hold the flange has cross threaded nuts and it's...

Is there a YouTube Video or write-up on how to take apart the hub and inspect the bearings? I found one video where the guy already has the hub taken apart. I'm not even sure how to get to that point. In the picture below, the nuts labeled "A" and "B" that I un-tighten are just spinning freely...

SOLD Locking Hub Adapters these allow you to replace your Toyota Electric Locking Hubs on a 70 series with Aisin or other manual hubs. The adapters are brand new and were never used and include gaskets, etc. SOLD

I bought an Aisin FCT-004 from Amazon and what I receive was the one on the right. Everything bolted up except when it was time to mount it on the water pump. The one on the left is what I purchased from Rockauto.com which is the correct one.

Hi guys I'm about to get in and tighten down my front wheel bearings. I'm finding mixed info on torque specs for the 6 nuts that hold on the flange and cone washers on the outside of the hub. The ones you see when you first take the center caps off the wheels. Can someone confirm the torque...