housing

Aire cleaner housing from an Fj60. The lip appears to be deformed slightly in one area, although you wouldn't notice it unless looking for it. The hole for the carburetor stud is a little wallowed out, see photos. $100, buyer pays shipping.

We're pretty far along in a front axle rebuild and have fiund the axle housing to be bent. Unfortunately this wasn't noticed sooner. It's bent outboard of the lower control arm bracket, and before the spring perch. I can see the bend and can picture putting it in a press to straighten it, in...

I was having an issue with my thermostat reading temps of 140F to 160F, never reaching the operating water temp of 180F. A cool engine sounds cool but its really not, Oil only cleans when its at operating temp and the engine is optimized to run at 180F. I already had drained some coolant when I...

Full rear axle assembly from a 1996 land cruiser, FZJ80. Hub to hub. Compatible with ABS and non-locker. Has disk brakes with fairly new calipers. Has rust. 4.10 gears. Complete with all parts, lines and sway bar included. $695 OBO Prefer not to ship, but will and buyer pays costs. I get pretty...

I have 3 rear and 2 front axles from fj62. Willing to sell as they sit, with or without 4.11 third members and inner axles/cv. All need new seals at a minimum. Can sell painted and fully rebuilt as well. Located in MD. Willing to ship. Reasonable prices depending on if I need to prep to ship and...

Have a brand new in the box PS housing ready to be built with a mini truck components to outfit your 40 with factory power steering. Toyota PN 44107-26030 $500.00 shipped in the lower 48.

Later FZJ80, straight and solid unlocked axle housing available. Can include knuckles, relay rod and a few other bits and pieces still on the housing. Does not include shafts or birfields. Have third with carrier but without ring and pinion. Ideally can sell this to a local to avoid the...

Need a thermostat housing pair (upper and lower) with no rust or corrosion issues. Thanks!

Looking for a housing for HJ45 - the lower thermostat housing for H1 diesel 1980's Australian Landcruiser. NOT for H2 diesel. Will paypal, venmo, bitcoin, card, overnight, whatever i need to. Not the upper. I have that and the thermostat itself.

So my intake on my '78 is bone stock, but I have noticed that there is more of a gap on the back side of my carb/air cleaner housing than there is on the front where the top of the housing meets the gasket. I do not believe my housing is tweaked but with this extra gap on the backside I have...

Used pickup power steering gearbox housing, free + shipping from 20912. I used the innards for a 40-series ps gearbox rebuild & didn't want to toss this out if someone could use it. There was some crud in the bottom (see pictures) but everything looked okay.

I thought this might be the best place for this but if not let me know. In the back of my mind I have been planning on building a full float rear axle for my 2001 tacoma. This would be the first time I have tried to build an axle like this, so I am hoping to get some advice from those that...

Looking for a 4speed bell housing for a fj40. Perfer in Atlanta,Ga area. Thanks

Redoing the plumbing on my 2FE and trying to decide which housing I'm going to run for the thermostat. I have a question about the 2F with oil cooler: In this photo, cool water is flowing FROM the water pump -> oil cooler -> thermostat upper housing, correct? I don't really get that...

Lower t stat housing with temp sensor. Front right threads have been rethreaded but still in good condition. $25 paypal fnds n fam. plus shipping .

Trying to get through to change the clutch on a 77. I removed the two top bolts and 3 per side on the bell housing then with trans and t case (and engine) supported tried to wobble/force/move everything back. When I got frustrated with that, I disconnected the four bolts around the trans and...

I've looked on the forum but can't find an answer. I have the 2 sets of front turn signals shown in the pic. I'm trying to figure out if the Grey or black housing color is correct for my 78. I see them both for sale new here and there but can't seem to find info on when the switch was from...

1978 FJ40 The lower portion of my heater blower unit (that bolts to the passenger side firewall) is broken and missing a good chunk where it meets the louvers on the cowl. My fan motor works fine, not sure if anyone would part with/sell just the housing? Of course Id like one that is not...

Did a search and came up empty. Anyone know of a source for the lower thermostat housing for a B engine, 2-hole base plate? There are none that I can find in the Philippines. Thanks.

Hi All, I recently new to the LC200 family, picked up a 2010 LC. I am wanting to switch out the front headlight housing to the look of the 13' - 15' with the running LED and projector lens. (Apologies if this is cover already somewhere) But I am wondering if I buy the OEM housing for a 13' if...