flywheel

I have a 1984 fj60 with a 2FE conversion with H55f. I replaced the clutch and flywheel a while back ago and when i removed the old flywheel it had groves worn in on the engine side of it that the new one didnt have. And where you press in the rear main seal the metal on the block is flat, shiney...

Looking for the size of bolt for the clutch flywheel on an 82 fj60. Thanks!

I have this fascination with a manual 1fz in my cruiser. While browsing the Internet, I stumbled across this offering from Fidanza. It's states it's compatible with the 1fz-fe in a 97 landcruiser. Were there some changes made between 96-97 that I'm not aware of? Would this be a viable option...

Located in Wilmington, NC. Looking for parts for an 85 FJ60. -Flywheel cover -4wd emblem -rear wiper motor -center console -rear bumper Thanks

doing an engine swap and pulled the clutch to find this. Thoughts?

I can't find the little mark on the flywheel. There is a part of the flywheel that looks like it has about a 1-inch cutout, but I can't see the mark. Have rocked the engine around a revolution and still can't see it. For right now, I advanced the timing until i can just barely force a ping...

70 - 74 Toyota Land Cruiser FJ40 -- Clutch Items • Cutch kit has < 20 miles on it • Flywheel since resurfacing < 20 miles on it • Clutch fork • Bearing hub with clips Short story is previous owner of my '77 FJ at some point installed a 3-speed in it. Clutch went out and I tried to replace what...

1997 LX 450: is there a shim that goes between the flywheel and the crankshaft? The engine was rebuilt and a new starter was installed but the vehicle sounds harsh as it starts up. I replaced the starter but sounds the same. A friend told me that there is a shim that goes between the flywheel...

Stock 72 FJ40 with 1F and 3 spd trans +tcase. I'm in the middle of a clutch/rear main/oil pan gasket job. Below is the picture of my flywheel after getting it resurfaced. There are small heat cracks all over it which didn't fully machine out. You cant feel the cracks with a fingernail. Any...

I think this came off a 2F bellhousing. $45 plus shipping.

for sale from 10/1985 fj60: 2f flywheel - 100$ Radiator, great shape no leaks - 100$ choke cable and switch - 50$ located in 97223

finally figured out how to hot wire the starter so it spins and the pinion pushes out! Going to try and loosen the crank nut on my 85 60 so I can put in a new front main seal. It's been a battle and I hope this does the trick! Quick question for the mud-gods: anyone ever do the starter bump and...

I have a 04/1976 2F with 4spd that is missing the covers under the flywheel. It should be a two piece setup with a sort of flat cover up against flywheel and a rounded pan-like cover underneath the flywheel. Should be part numbers 11363-60010 and 11361-60060 If anyone has either of these parts...

Well I have searched the vast expanse of the forum and internet, only to come away still confounded. i am trying to mate the engine and transmission, ensuring the flywheel bolt holes and torque converter bolt holes align. My son and I can't seem to crack this particular nut. 1. Is there a...

I have a 76 40 and I ordered a FSM but it hasn't arrived yet. My question is what is the flywheel tooth count and what is the diff ratio? Any help would be greatly appreciated. Thank you. I used the search feature and couldn't find an answer to my questions. I must be search feature...

I just removed the starter from my BJ70 (Ugghhh) after troubleshooting a clicking noise. Both solenoid contacts were replaced, the battery side contact which was totally eroded just happens to be used on Dodge Cummins trucks, so easily obtained. Once installed the starter turned over the engine...