fj60

I apologize if this information has already been discussed, but I was unable to find my combination of questions. I have a 10/85 FJ60 with a Holley Sniper. Currently I am running the frame rail pump, but am in need of more fuel capacity on many trips. Jerry cans aren't especially practical with...

Hi All, Recently my FJ60 has started leaking coolant into the passenger side floor board inside the cab. Must be coming from the heater core which is a big job to replace since you have to take out the entire dash. My FJ60 is my daily driver during the warmer months and I don't want to have it...

Updated for accuracy - My wife’s truck is grey interior. She would prefer the brown. I have ordered carpet and am working on new seat covers. I still need - Seat belts cargo area panels or patterns for panels dash top (may just paint the lower and use a carpet cover.) steering wheel and...

After much debate I’ve decided it’s time to sell my 1985 FJ60. Purchased at 179k and it’s currently at 183,267k. I’ve had it for almost 4 years now and bought it as a project truck that I would slowly build. Just don’t have the time and money to keep going. I don’t use it like I should and it...

Boxed and ready to ship. $500 obo shipping included to the continental U.S.

Rare opportunity to own a low mile FJ62. Minimal body rust, frame is solid. Runs and drives good. Some would say it needs a paint job while others enjoy the fading and patina. I just had it on a 600 mile trip and it got 16.2 miles per gallon, she cruises at 75 miles an hour with all the gauges...

FJ60 Axles with stock 3.70 gears. Front axle (no knuckles): $200 Rear axle has a Lockrite locker and is complete: $300

Selling the power steering gear box off of my 1984 FJ60. It works great and includes the cover for the u-joint. I can include the power steering cooler and lines if you want them. $400 obo Willing to ship

Selling a factory transmission/transfer case skid plate off of a 1984 FJ60. I am willing to ship. Looking for $50

Looking for an AC hard line for a FJ60 as shown circled in red in attached picture.

Before I go buy a new one, does anyone have a second hand one they would sell on the cheap? Looking for the style where the studs point straight down

Replacing charcoal canister on Fj60 - outer vent control valve absolutely disintegrated when taking hoses off. Located in DFW.

jbk said: Looking for a source for passenger rear quarter panel. Pretty much down from top of gas cover down and back. Caught a tree.

Looking for a source for passenger rear quarter panel. Pretty much down from top of gas cover down and back. Caught a tree.

I have a brand new Cruiser Teq Rebuild kit with the Koyo Bearings, the whole kit is made in Japan with the bearings. Brand new in box. 150$ plus you pay shipping. Only opened to take a picture. I threw in some other new gaskets I had for the hubs. I will take PayPal GS if you pay the 3%.

Hi all, I recently had what I thought was a blown out master clutch cylinder. I ordered a new Aisin CMT012 from Rock Auto and installed it. I tightened it down and went to bleed it and noticed it was leaking terribly from the fitting. I took it back off and compared to the old MC and noticed...

1986 Toyota FJ60 in 8B2 Blue with 174,400 miles currently. I purchased this out of Pennsylvania as a project and have since put a lot of time and parts into getting this back into somewhat of its original glory. Being an east coast vehicle it certainly wasn’t spared from salt and corrosion but...

I have a chrome less windshield gasket from City Racer. Ill sell for 70$ plus you pay shipping. It does not have the cut out for the chrome inserts bc I was reading how much of a pain in the A55 it is to save the chrome so I opted for the chrome less gasket.

I have a FJ60 OEM Carb, it is rough looking and will need a full rebuild. It was from a 1986. 50$ plus you pay shipping. Ill do whatever payment method you want, but you pay the extra fee for G&S

As the title states, looking for one of these jacks. They would be found in an FJ45 pickup or Troopy from 08/80 to 12/84 (-60020 and -60040) or in an FJ60 from 08/80 to 03/85 (-60030 and -60040). Interested in accompanying jack tools as well.