Hello all.
Going to try and keep this concise and clear.
1994 triple locked Land Cruiser. Previous owner re-geared it to 4.88s. Still running stock tires.
My question is- will the factory center lock (and the rear and front locker for that matter) still work as normal with a regear?
The...
Heyo,
Been researching here and other places. Just bought an 08 Lx570 with 173k miles. Center Diff will not engage. I've tried to engage it several times through any number of recommended scenarios and haven't been able to get it on.
My question is, if I can't get it on, what kind f repair...
Can someone get me the measurements of an unbroken center console lid latch? Mine broke for the third time and I want to try something else to repair and make sure it works. Thank you in advance. No I'm not 3d printing going to make it out of metal.
Sharing a few photos of my dometic center console build. I paired it with the 2nd battery tray under the hood, paired with a Costco group 27 marine battery (88 amp hours?). The solar is a flexible 55w panel that just barely overhangs the dashboard. In the summer I've been getting about 2.2amps...
Freshly powder coated front sleeves and rear center caps in black. Came off my 1990 62. Small center dent on one rear center cap.
Located in North County SD. Can ship or meet up within a reasonable distance. $150 plus the ride.
Hello, just bought a ‘04 LX470 and it is missing 1 of the wheel center caps w/ gold L. If anyone has one laying around or a full set of the ones w/ the silver L I will be happy to buy. Thanks in advance…
Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month.
To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...
Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month.
To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...
Hello all, just wanted to post this up for the benefit of all LC200 owners. I cut open the stock center muffler in hopes that I might get it to flow better. What I saw is quite shocking. It is extremely restrictive, excessive even.
I just got my 03 LX a couple weeks ago and knew when I bought it I would have to get an alignment. They had to recenter the rack because the TREs were maxed out. I assumed this was the original rack but maybe it was replaced. The PO didn't mention it and there was no record but it does have...
Looking for 1 wheel center cap for 97 LX450 in brushed silver to replace one lost in traffic. Would buy 2 or a full set if needed. Would be willing to pay shipping to socal.
When I bought the truck, the plastic was all cracked and broken so i pulled it off along with the adhesive below. Got a buddy of mine with a leather shop to cut me out a piece that fit perfectly.
2015 200-Series Land Cruiser
About 90,000 miles. Not my daily driver. I drive the vehicle one to two times a week for short distance/duration. I drive the vehicle in L4 for short distances twice a month. I have not regularly used the center differential lock.
Had the four-wheel drive serviced...
Hey,
Writing this to see if anyone has run into this issue and what the solution is. I am currently working on the steering cause it seems to work better when the ball joints aren't all friction welded after 42 years. Anyways, I purchased a center pin rebuild kit from Cruiser Corps. The...
Early - 6/1969 Steering Center Arm
Wanted to post up a thread on the partial rebuild of my center arm. I say partial because my center arm shaft and the bearing races were undamaged. If you need a new shaft I think that Mark's Off Road and Cruiser Outfitters still have some. If the races...
The center muffler on my '03 is in need of replacement. My go to online store is $460 shipped. The local custom muffler shop quoted $160 for steel and $220 for stainless. I generally go with OEM as I'm usually saving $$ on labor by DIY'ing, but not sure in this case - is the OEM part worth...