Recent content by NB100LC

How about this? https://www.mcmaster.com/products/tubing/id~11-000mm/id~11-000-mm/id~11-0-mm/id~11-mm/ 20' 11mm id, 16mm od, clear. If someone tries it let me know if it works. I'm pretty sure my sunroof drains are compromised as I always hear gurgling sounds from there when it rains.

2001 100 series Sanity check me please. Trailer brake controller red wire should be connected to green with white stripe at the tail lamp/brake light switch? This is how I have mine connected, it’s soldiered, I just inspected this connection and all appears well. *plan on checking voltage...

Please somehow try a new or different battery, yours may seem healthy as mine did, but this is a signal something isn’t -perfect- for the abs/vsc/atrac computer. trust me, it makes no sense to me then or now, that battery I replaced would still crank the engine strongly and would start within...

I had the same issue come up about a year ago, out of the blue as you've described. It ended up being the battery. I had checked it with my DVM, had 12.5v off and 13.7 running. Took it to auto-zone, had the battery tested and it checked out good. Fortunately my '02 tacoma also uses 22r, so...

Just received this in the mail from Duane @ MCSSPECIAL, rear axle retainer, tone ring, and bearing puller tool. New plate is developed to fit our 100 series axels. Now all I need is the bearings to arrive at @cruiseroutfitters from Japan.... been waiting a couple months already... Darn you...

Those are nice, who makes them? From appearances the look to be 16” as well... can you post a link to the website?

I hadn't noticed any issue prior. Looking back at local almanac info the temp would've been ~40-45F. Snapped this photo of my hand -after- the blood had returned to my fingers. I still have a scar on my middle finger...

Just before HIH8 I was routing coaxial cable along the drivers windshield and through the cowling/hood for CB communications. It was cold and I was focused on the task - I was working at the cowl area and not the firewall. the hood had slowly begun to close itself and my left hand was on the...

Sorry for your troubles! I used a press to install the replacement. Removal of the original was to press out the rubber, then saws all the shell just like you did. With a press, the correct size socket or press sleeve and old one removed it’s a 5 minute job (at the press).

i use a WD hitch with our travel trailer. It’s smaller and probably lighter than what you’re considering (19’ and somewhere to around 3k# dry) my hitch bars are 750# but I’m by no means using their full strength. Trailer pulls like a dream.

https://www.suspension.com/superpro/products/toyota_landcruiser_series_100_2001 Super pro bushing for the drivers side front support. Part Number: spf3575k Super pro steering rack bushings can be either Part Number: spf2470k LHS and RHS, Only fits vehicles up to 08/2002 or Part Number...

Did this. SuperPro polyurethane extended rear sway bar links and the bar "D" shaped bushings. https://forum.ih8mud.com/threads/superpro-polyurethane-bushings-for-lc-100-series.662918/post-12889750

Did the SuperPro rear anti-sway bar this evening after I got off work. Used their extended links and hardware. old stuff was shot @ 212k miles, especially the bushing in the end of the bar, it was beyond loose...

Wow, that filter is massive compared to stock. It clears the drip deflector ok? Wish i had known this, just bought a case of 90915-YZZD3 off of ebay last week. I see that there's a case of these available now for 40 bucks...

I've searched you tube for this video, found the channel. Haven't yet been able to find this video. Could you provide a link?