TTT -- The Tool Thread (5 Viewers)

[fourtrax]

Anyone need a very used 12 ton press or a 14" abrasion saw. They both have issues but work. Tired of stepping around haven't used them since they were moved to second string.

Cost = your ride

 

[coinoperated40]

Anyone need a very used 12 ton press or a 14" abrasion saw. They both have issues but work. Tired of stepping around haven't used them since they were moved to second string.

Cost = your ride

View attachment 2746523

View attachment 2746524

Is the saw used to cut metal? I’m guessing? I could borrow it for a little then pass it on if possible.

 

[fourtrax]

fine with me

 

[Pick]

Anyone need a very used 12 ton press or a 14" abrasion saw. They both have issues but work. Tired of stepping around haven't used them since they were moved to second string.

Cost = your ride

View attachment 2746523

View attachment 2746524

I'll take the press if it's still available... PM me and we can coordinate

 

[fourtrax]

it's yours.

 

[Pick]

it's yours.

Thanks so much for the press, and the tour of the 80, 4runner and greaser....

 

[NCFJ]

Who is gonna take the plunge?

Ultimate Mechanic Chair--50% OFF

Share & Get Get $3.00 Discount! TIPS Our goods are authentic with genuine patents counterfeit must be investigated Customers please identify our products Limited to 180 pieces Restore original price when sold out You can return items for a refund or exchange within 30 days Shipping gt gt...

www.ziwins.com

 

[Green Hell Mustang]

Who is gonna take the plunge?

Ultimate Mechanic Chair--50% OFF

Share & Get Get $3.00 Discount! TIPS Our goods are authentic with genuine patents counterfeit must be investigated Customers please identify our products Limited to 180 pieces Restore original price when sold out You can return items for a refund or exchange within 30 days Shipping gt gt...

www.ziwins.com

I'm afraid to look at the price.

 

[jynx]

Must be a scam or a bad link. Shows $39.99...

 

[NCFJ]

I am thinking Scam

 

[cruiser4life]

No doubt about it:

 

[Malleus]

Just got off the phone with Heather from Metals Depot in KY. Last week I bought a 3/4" and a 7/8" cut length of TGP. The 7/8" came turned but not much else. I sent them a photo and they're sending me another tomorrow. I would highly recommend them for metals to anyone needing stock.

I'd much rather buy from Alro in Charlotte, but due to the government paying people not to work, they can't get their plant open.

 

[GLTHFJ60]

Made this tool yesterday to do a job with @Fort Knox . Can anyone guess what it's for? Two plasma cut plates (top is 5/8" a36, bottom is 1/4" a36) with two lathe turned tubes, all glued together.

 

[fjc-man]

Hmmm, press fixture for rear ( sealed ) wheel bearings?

 

[GLTHFJ60]

Hmmm, press fixture for rear ( sealed ) wheel bearings?

That didn't take long, lol. Exactly right. We tried pressing out the first axle shaft and bent the spare brake backing plate into a pretzel, so we built this tool to press the rest without damage. Worked a treat.

 

[fjc-man]

That didn't take long, lol. Exactly right. We tried pressing out the first axle shaft and bent the spare brake backing plate into a pretzel, so we built this tool to press the rest without damage. Worked a treat.

The one you fabricated works for which model Toyota?

 

[GLTHFJ60]

The one you fabricated works for which model Toyota?

Built it specifically for 2nd gen 4runner axles, but it should work for other mini models as well.

 

[Malleus]

Finally got the last piece of inventory over the weekend. After a 26 hour trek to PA and back through a most ridiculous rainstorm in VA, the surface grinder is finally home. It's a Thomson model D manual 6x18.

Now all I have to do is take it apart and remove all the stuff that's inside that shouldn't be there. This thing is a beast, even though it only has a 30x30 inch base, it weighs a ton! I couldn't have moved it without some help from the nice folks at Sunbelt.

 

[S4Cruiser]

Those trailers are tits!

Nice grinder too!

 

[GLTHFJ60]

That grinder is GORGEOUS!