Transmission Preventive Care While Engine is Out

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 13, 2016
Threads
66
Messages
1,450
Location
Los Angeles, CA
Okay, I tried to search for this, but didn't see conclusively a list of things I can do. I am confident with the motor and that rebuild. I am working on a 1997 80 Series.

I bought my truck with 300k with a bad HG...pulled the motor and transmission together.

My motor will be done in about two weeks. I wanted to proactively do any maintenance items while its out. Is there anything with the torque converter or flexplate or bellhousing?

Or just plan to do a fluid flush and filter once its all back in the truck?

Thanks for any advice here!!!!!
 
You might consider replacing the seals at the input and output. Output seal replacement requires separating the transfer case.

My 93 has a wire mesh filter that can be cleaned and reused. When I dropped the oil pan on mine at 268k right after I purchase it, the transmission was very clean inside with nothing stuck on the filter screen.
 
You might consider replacing the seals at the input and output. Output seal replacement requires separating the transfer case.

My 93 has a wire mesh filter that can be cleaned and reused. When I dropped the oil pan on mine at 268k right after I purchase it, the transmission was very clean inside with nothing stuck on the filter screen.

Nice! Okay, that's good info. I will take a look at that!! I have no idea how the previous owner cared for the vehicle...I have a lot of money into the motor rebuild and just hope the tranny doesn't have issues soon.
 
Typically the transmissions outlast the engines. I have the earlier A442 trans that is known to be more brutish and over built than the later A343 that Toyota switched to in 1995. At 281k my tranny works great but so does my engine. Someone must have taken care of it.

If you search this forum, you won’t find much talk about transmission issues period.
 
Typically the transmissions outlast the engines. I have the earlier A442 trans that is known to be more brutish and over built than the later A343 that Toyota switched to in 1995. At 281k my tranny works great but so does my engine. Someone must have taken care of it.

If you search this forum, you won’t find much talk about transmission issues period.

Yea, I agree. That seems to be what I've heard and reason I probably wasn't able to fund much for PM work...Just thought I'd check with you all so be safe though. Thanks again for the info!

My rebuild is all stock. I don't plan to do much other than some fire trails and very low key offroading.
 
Souns great. Post up some pics and info on your engine and maybe a review of how it turns out and your overall experience with the shop you used. Others could benefit from your experience.
 
Last edited:
I'd replace the input seal for sure.

Then as you say, once the tranny is re-installed, drop the pan and clean or replace the filter. With the mileage on your rig, you might consider increasing the line pressure while you have the pan off. Takes about 30 seconds.

You might get a little increased life out the friction discs that way.

LC trans adj1.webp


LC trans adj2.webp
 
Lies. :flipoff2: It might weigh more than an A343 but so does a ship anchor. A343 has been proven to take more abuse than the A442, look to AUS to see them having all kinds of issues with the 442 once a little more power is added.

Typically the transmissions outlast the engines. I have the earlier A442 trans that is known to be more brutish and over built than the later A343 that Toyota switched to in 1995. At 281k my tranny works great but so does my engine. Someone must have taken care of it.

If you search this forum, you won’t find much talk about transmission issues period.
 
Typically the transmissions outlast the engines. I have the earlier A442 trans that is known to be more brutish and over built than the later A343 that Toyota switched to in 1995. At 281k my tranny works great but so does my engine. Someone must have taken care of it.

If you search this forum, you won’t find much talk about transmission issues period.
All I can say is that after seeing what all you guys do to these trucks off-road and noting that nobody seems to have any tranny issues, it makes me feel good about the fact that my mall crawler with 262,000 probably never will either. :)
 
I'd replace the input seal for sure.

Then as you say, once the tranny is re-installed, drop the pan and clean or replace the filter. With the mileage on your rig, you might consider increasing the line pressure while you have the pan off. Takes about 30 seconds.

You might get a little increased life out the friction discs that way.

View attachment 1628212

View attachment 1628213

Does increased line pressure firm up the shifts? I have to look through my notes but I recall seeing that the previous owner of my cruiser had a "shift kit" installed when the transmission was rebuilt (around 2003, not quite sure about the story why). The shifts seem normal to me with the exception of 1st to 2nd in 4low which is very abrupt.

He said that the goal behind the shift kit was to extend the life of the transmission (seems to be working as this was 200k miles ago and it been fine since).
 
I'd replace the input seal for sure.

Then as you say, once the tranny is re-installed, drop the pan and clean or replace the filter. With the mileage on your rig, you might consider increasing the line pressure while you have the pan off. Takes about 30 seconds.

You might get a little increased life out the friction discs that way.

View attachment 1628212

View attachment 1628213

Hey thank you for this information. I had never heard of this previously.

Lies. :flipoff2: It might weigh more than an A343 but so does a ship anchor. A343 has been proven to take more abuse than the A442, look to AUS to see them having all kinds of issues with the 442 once a little more power is added.

That makes me feel better!! Haha. Thanks!!!

All I can say is that after seeing what all you guys do to these trucks off-road and noting that nobody seems to have any tranny issues, it makes me feel good about the fact that my mall crawler with 262,000 probably never will either. :)

Yea, I rarely hear of any trans issues. Other than what other have said about the input seal, I am guessing I will be good!
 
Does increased line pressure firm up the shifts? I have to look through my notes but I recall seeing that the previous owner of my cruiser had a "shift kit" installed when the transmission was rebuilt (around 2003, not quite sure about the story why). The shifts seem normal to me with the exception of 1st to 2nd in 4low which is very abrupt.

He said that the goal behind the shift kit was to extend the life of the transmission (seems to be working as this was 200k miles ago and it been fine since).

IF you already have a shift kit (and properly adjusted cable)....I would not think increasing line pressure (via the primary regulator valve) would be worth your while. It's just an easy thing to when folks already have the pan off the transmission. In my case...it resulted in firmer/faster shifts, but you really don't notice it unless you are accelerating hard.

Toyota's 'purpose' for providing an adjustable primary regulator valve...is anybody's guess. I suspect the transmission/valve body was designed to be used in vehicles with varying requirements.

Anyway, I have not experienced any downside to raising the pressure in my aging transmission, but I would think a dedicated 'shift kit' would be the better way to go if a person were looking for noticeably firmer shifts.

This applies only to the 343 transmission.

VB_A343F trans.webp
 
I'd replace the input seal for sure.

Then as you say, once the tranny is re-installed, drop the pan and clean or replace the filter. With the mileage on your rig, you might consider increasing the line pressure while you have the pan off. Takes about 30 seconds.

You might get a little increased life out the friction discs that way.

View attachment 1628212

View attachment 1628213

90311-38029 - Toyota Parts Deal @baldilocks &
@flintknapper Do you know if this is the input seal that I need?
 
Please post pics of the seals replacement. Thanks!
 
Looks to be correct, but you might receive a part with a different part number (possibly super-ceded).

Thanks!!! I was doing some more research and I stumbled upon 90311-38020 Perhaps this is the current one.
 
Thanks!!! I was doing some more research and I stumbled upon 90311-38020 Perhaps this is the current one.

I'm sure there have been superceded numbers over the years. Best to check with your Toyota Parts Dealer.

Typically, parts are specified for a particular manufacture time period. Changes/Improvements to parts generally require a new part number though the part might be interchangeable or backwards compatible.

A good parts dealer can tell you what is most current.

Front Seal.webp
 
I'm sure there have been superceded numbers over the years. Best to check with your Toyota Parts Dealer.

Typically, parts are specified for a particular manufacture time period. Changes/Improvements to parts generally require a new part number though the part might be interchangeable or backwards compatible.

A good parts dealer can tell you what is most current.

View attachment 1640142

Thank you!!! So this would be considered the input seal? Thanks again!!!!!
 
Okay, so now I am really confused. I called a local Toyota Dealer and they said 90311-38020 isn't even meant for my truck...and I actually need 3 seals that make up the input seal.
 
With that many miles, one of the other items i would be think about replacing, would be all the shift solenoids. YMMV
 
Back
Top Bottom