Transfer Case Shift linkage Photo NEEDED!

[Midgainc]

NEEDED ASAP!

I have the drivetrain installed. I just cannot remember how the transfer case shift linkage was hooked up. Can some of you guys post some photos from different angles that show how the 3 speed set up.

I would like to look at a any. Thanks.

 

[threadchaser]

3 speed linkage

Let me know if you need more.

The blue tape is how I leave reminders for myself "Yo, something needs to be done here." In this case the bottom of the handheld shift level is disconnected.

 

[tucker74]

Here's the best I've got:



Tucker

 

[Midgainc]

this is a big help. i hope this is enough to figure it out.

 

[Midgainc]

where could i get a dustboot like the one in the threadchaser's first photo? i didnt know one went there!

 

[scrapdaddy]

I think mine came in the rebuild kit, but PM Georg ( Orangefj45 ), he should have some.

 

[tucker74]

Kurt or Mr T

Tucker

 

[cruiseroutfit]

where could i get a dustboot like the one in the threadchaser's first photo? i didnt know one went there!

Call me

T/C 2wd-4wd Shaft Boot - $6.50 each
Transfer Case 2WD - 4WD Selector Shaft Rubber Boot
(Fits 1963 - 7/1980 40/55 Series with floor mount T-case lever)
Part# TCB60010
http://cruiseroutfitters.com/engineparts.html

 

[Midgainc]

I started looking at my parts for hooking this back up. It seems like I am missing the linkage with the blue circle around it. What is the likelihood of finding one of these laying around? I may need to borrow one so that I can have one made.

Any one up for that?

 

[threadchaser]

Sure. PM me your mailing address. It'll go out tomorrow by the USPS slow boat. Keep it, gratis.

 

[threadchaser]

3 speed T/C linkage

Done. USPS has it now.

For anyone's future reference, the rod is 119mm center-to-center.

 

[PabloCruise]

Sure. PM me your mailing address. It'll go out tomorrow by the USPS slow boat. Keep it, gratis.

Good Cruiser Karma to you...

 

[cruiseroutfit]

Good Cruiser Karma to you...

x2

 

[Midgainc]

Threadchaser, I got the part today! Thanks so much. I am going to clean it up and install this week. You saved me from a huge headache.

 

[threadchaser]

De nada. The world needs every pig we can keep on and off the road.

 

[Midgainc]

I having trouble hooking up the lower end of the linkage to the shaft where the new boot is. Any ideas? The shaft has a groove cut into it and no threaded anything. The linkage has a hole in the bottom of it like it is supposed to be bolted. I am at a loss!

 

[tucker74]

There is a little plastic disk piece that fits in that hole and seats in the shaft, SOR calls it a "drive shoe". It looks like it's available new so you should be able to get it still, or look through your parts

Tucker

 

[threadchaser]

Here is what the one out of a 6/72 fj55 looks like assembled.

 

[Midgainc]

Thanks. I have ordered one from SOR, and hopefully, when it arrives, installing this will complete my T-case linkage install! This must have been missing when we removed the drivetrain back in Sept. I never saw anything like this little piece. Without it, I guess you couldn't control the front wheel drive from inside.

Thanks again for all of your help!

 

[Midgainc]

part is in, and now we are going to give it a shot. Thanks for all of ya'lls help with this. Some of this stuff is not obvious.